Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.

The latest SmartSDR Software:
SmartSDR v4.1.5 | SmartSDR v4.1.5 Release Notes
SmartSDR v3.10.15 | SmartSDR v3.10.15 Release Notes

The latest 4O3A Genius Product Software:
The latest 4O3A Genius Product Software and Firmware

How to Receive Technical Support::
If you are needing assistance with FlexRadio products, please refer to the product documentation or check the Help Center for known solutions. Need technical support from FlexRadio? It's as simple as creating a HelpDesk ticket.

SmartSDR CAT

For discussions related to interfacing your FLEX-6000 to third-party software and hardware via the CAT protocol, this is the category for those discussions.

New Discussion Ask a Question

Sort Hot ▾

• Hot
• Top
• New

Discussion List

Discussion	Started By	Replies	Views	Most Recent
CW with ALS 600 Answered ✓	Bob May 2023	3	121	Bob May 2023
Logger 32 with Flex 6300 Answered	MM0DGI May 2023	2	154	MM0DGI May 2023
Moved: 6600 com port conflict with N1MM, CW not sending properly Closed	Mike-VA3MW May 2023	0	1	Mike-VA3MW May 2023
N1MM and WSJT-X setup	KM4CQG April 2023	2	350	KM4CQG April 2023
COM port dedicated to a program but sensitive to the slice in use to Tx Answered	Piero Ferrua March 2023	5	243	Piero Ferrua April 2023
SSDR V3 CAT not communicating on existing serial port Answered	DaveAB3I April 2023	13	384	David Decoons, wo2x April 2023
ARI-500 with 6400 M Answered	Bob April 2023	2	152	Bob April 2023
Moved: No changes to computer or LAN 6300 Closed	Mike-VA3MW April 2023	0	1	Mike-VA3MW April 2023
Moved: Flex Control Closed	Mike-VA3MW February 2023	0	1	Mike-VA3MW February 2023
Problem with adding virtual ports	Slawomir February 2023	9	438	Slawomir February 2023
No RF Output using WSJT-X to Smart SDR Answered ✓	Ron Miles February 2023	2	218	Ron Miles February 2023
CAT.settings Read-only attribute	marwalk February 2023	0	83	marwalk February 2023
Setting up up new cat ports for MMTTY	smprior52 February 2023	2	163	smprior52 February 2023
SmartSDRcat not creating new ports Answered	Andrew O'Brien December 2022	2	163	Andrew O'Brien January 2023
Smart Cat	w9kjo December 2022	9	390	David Decoons, wo2x December 2022
Filter width after clicking spot	Rich McCabe November 2022	3	164	Rich McCabe December 2022
CAT creates the wrong port number	N5NHJ November 2022	2	152	Butch December 2022
TX Band Settings	w9kjo December 2022	1	101	w9kjo December 2022
Moved: How do I make Flex respond to StepIR tuning relay using WSJT-X? Closed	Mike-VA3MW November 2022	0	1	Mike-VA3MW November 2022
how do I remove the CAT com ports? Answered	ON5AM June 2017	13	255	Andrew O'Brien November 2022
Cannot unintall FlexVSP	Uli DF5SF October 2022	3	203	Uli DF5SF October 2022
Moved: N1MM+ not keying amplifier Closed	Mike-VA3MW October 2022	0	1	Mike-VA3MW October 2022
How do I get WSJT to activate transmit for 6700 Answered	Rich Roby October 2022	2	174	Mike-VA3MW October 2022
CAT Losing Ports	rtalexand September 2022	0	72	rtalexand September 2022
Lost CAT control	Dougrea November 2021	17	580	Duane_AC5AA September 2022
Unhandled Error SmartSDR CAT (v3.1.8.221)	Torrey Mitchell October 2019	4	327	Stef September 2022
CAT control of Panadapter zoom, rate and other parameters? Answered	sdelmont September 2022	1	114	KD0RC September 2022
Manually keying the transmitter in DAX mode Answered	STEVE_KW5TX September 2022	9	287	David Decoons, wo2x September 2022
How can I get my CAT controls working again? Answered	rmanzer August 2022	1	103	rmanzer August 2022
CAT will not automatically open	Steve Blankinship AG4SO May 2022	8	262	Mike-VA3MW June 2022

New Discussion Ask a Question