Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.

If you are having a problem, please check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

Need the latest SmartSDR and Power Genius Software?

SmartSDR v3.1.12 and the SmartSDR v3.1.12 Release Notes. | SmartSDR v2.6.2 and the SmartSDR v2.6.2 Release Notes.
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes. | Power Genius XL Firmware v3.4.16. | Power Genius XL Utility v2.2.10.

SmartSDR CAT

For discussions related to interfacing your FLEX-6000 to third-party software and hardware via the CAT protocol, this is the category for those discussions.

New Discussion Ask a Question

Discussion	Started By	Replies	Views	Most Recent
CAT error	Slawomir February 25	1	29	Tim - W4TME February 26
CAT port won't connect to FLDIGI	James Del Principe February 12	10	78	James Del Principe February 16
CAT Smart SDR 3.1.12 total deleted	oreste g January 25	0	33	oreste g January 25
Lost Smart Cat configutration Accepted Answer	Lou KI5FTY December 2020	6	72	Lou KI5FTY January 8
BCD whit 2x 144mhz 2x 432mhz is it possibel ???? Accepted Answer	Bent November 2020	3	32	KD0RC November 2020
4 x slices and 1x CAT-port !!! Accepted Answer	Bent November 2020	2	51	Bent November 2020
Enable/Disable the sending the rig ID in CAT ??? Answered Closed	Bent November 2020	1	21	Bent November 2020
Vqlog setup with Flex-6600 running remote ??? Accepted Answer	Bent October 2020	1	22	Tim - W4TME November 2020
Flex 6400 stopped keying amplifier	N4FP October 2020	1	32	N4FP October 2020
Flexradio 6700 and Acom 700s amplifier	Robert PA5A October 2020	2	107	Robert PA5A October 2020
Noise reduction? Question	FrankMVentura September 2020	0	71	FrankMVentura September 2020
What are the default DSP filters?	FrankMVentura September 2020	1	42	Al K0VM September 2020
SmartSDR CAT Commands? Answered	K1ESE June 2019	2	33	FrankMVentura September 2020
PTT Com Ports not working	Dan KG0AQ September 2020	4	51	Dan KG0AQ September 2020
Can I use ports created by SmartSDR CAT with PowerSDR	N7BCP August 2020	0	1	N7BCP August 2020
SmartSDR CAT 3.1.12 Requires FlexVSP service to be installed. Assistance Needed	Rich - N5ZC August 2020	1	21	Rich - N5ZC August 2020
Repeatable Problem with OnniRig and SmartCat	Patrick August 2019	25	24	Patrick August 2020
Kudos to Flex and Tim	N5NHJ June 2020	5	1	N5NHJ June 2020
SmartSDR CAT Freeze Answered	Glenn Depp June 2020	7	11	Glenn Depp June 2020
SmartCAT 3.1.12 - Com port selection Answered	N5NHJ May 2020	8	4	Patrick May 2020
CAT command that will enable/disable DAX Answered	Adde Tjernberg April 2020	9	1	Kes-m0pkz April 2020
Unhandled Error SmartSDR CAT (v3.1.8.221) Question	Дмитрий Сычёв October 2019	0	1	Дмитрий Сычёв October 2019
Unhandled Error SmartSDR CAT (v3.1.8.221)	Torrey Mitchell October 2019	1	13	Mike-VA3MW October 2019
Can't Remove CAT Ports Answered	Mark Erbaugh September 2019	5	12	Mark Erbaugh September 2019
After second software update to Maestro running v2.3.9 it quit	Steven WA8Y August 2019	2	1	Ray - K6LJ August 2019
Suddenly, No Power Output (CW, FT8, RTTY) Answered	kg5udale . July 2019	2	21	Eric Gruff July 2019
AG switching time Answered	Sergey KN7K June 2019	8	3	Sergey KN7K June 2019
CAT gives error message	szawrotny April 2019	3	1	szawrotny April 2019
SmartSDR CAT will not connect to Radio on LAN	johnk0tg January 2019	19	24	Ted VE3TRQ January 2019
Smartcat won't load	Mark Erbaugh January 2019	2	26	Steven WA8Y January 2019