Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.

If you are having a problem, please check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

Need the latest SmartSDR and Power Genius Software?

SmartSDR v3.1.12 and the SmartSDR v3.1.12 Release Notes. | SmartSDR v2.6.2 and the SmartSDR v2.6.2 Release Notes.
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes. | Power Genius XL Firmware v3.4.16. | Power Genius XL Utility v2.2.10.

SmartSDR for Windows

Please use this category for any discussion related to SmartSDR for Windows.

New Discussion

Discussion	Started By	Replies	Views	Most Recent
SO2R Knobs for SmartSDR	Steve London September 21	5	76	John K3MA September 22
Only 2 Panadaptors available on 6600M	Don Achelpohl September 18	2	89	Larry _ W8LLL September 19
RX Audio Latency	Steve London September 17	1	65	AWe September 17
Remote CW Operation Latency Issue Status	jimworth September 17	0	69	jimworth September 17
Mouse wheel does not tune Answered	Lou Laderman W0FK September 7	8	67	Lou Laderman W0FK September 15
Question about Maestro internal battery 1 2 3 Answered	John K6VFR August 2017	86	76	John W9KXQ September 15
SAM mode and beat note. Answered	George M. December 2019	12	47	Bill N3HQB September 14
Can't reach my Flexradio-6400 ATU remote from home	Mikael September 13	1	27	VK7WH Winston September 13
Power Genius Panel Not Responding	Peter WB6POT September 10	3	45	Peter WB6POT September 12
No audio on 80 meters	AA1OU September 11	4	25	AA1OU September 12
Using N1MM Logger With SmartSDR/SmartCAT, FlexControl, and K1EL WinKeyer	Jim-WD5IYT October 2013	21	32	Craig_KØCF September 11
MacBook Air Question Answered	Neil Friedman May 19	12	12	Alan September 10
cwx panel - bug reports and a problem workaround	Chris May 12	12	54	Chris September 10
TX bandwidth audio for packet 9600 and VARA	Luis del MOlino May 16	2	16	Jeremy_W2JG September 10
Dear Flex. It is been 1 year since I reported the bug.	Sergey KN7K September 8	3	138	Trucker September 8
New to the rig and software. Multiple questions about 6300 and V3 software Question	Bill September 5	2	45	Bill September 8
CW sidetone 1 2 Answered	Greg February 2014	50	140	K1ESE September 5
New to 6400 ... need help for remote setup	W4AFK Bruno August 30	8	79	KI4P September 4
CW setup Newbie to 6400. Accepted Answer	kansasjohn September 3	11	66	KD0RC September 4
Why is MOX Button Grayed-out On Second Computer? Answered	Jeremy_W2JG September 2	6	42	Jeremy_W2JG September 4
Pulsating Noise While Transmitting Answered	Jerry - W2TXB October 2013	10	32	John Orjias September 3
Unable to get PC microphone to work Accepted Answer	Al Reeves August 26	18	112	Al Reeves August 29
Using FDX to set up your TX Audio	Mike-VA3MW June 25	4	62	Keith WA0BEU August 28
Tim explains S Meters	Mike-VA3MW June 11	19	44	Keith WA0BEU August 28
smartSDR 3.1.12 running remote has display problem	W5UN_Dave August 23	4	61	Tim - W4TME August 28
Frequency display covered by SPLIT and TX in flag Accepted Answer	K9SO August 11	10	44	N7VXA August 28
CW in SmartSDR ? Accepted Answer	Bill / VA3QB January 2017	17	186	KD0RC August 28
CWX Bug? No audio or sig after macro abort	W5WTH August 25	7	21	W5WTH August 27
How to get callsigns on the panadapterscreen Answered	ole puschl July 2018	6	59	JPPRITCHARD August 27
Laptop for SmartSDR recommendation	gromit86 August 25	4	32	gromit86 August 25