Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.

If you are having a problem, please check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

Need the latest SmartSDR and Power Genius Software?

SmartSDR v3.1.12 and the SmartSDR v3.1.12 Release Notes. | SmartSDR v2.6.2 and the SmartSDR v2.6.2 Release Notes.
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes. | Power Genius XL Firmware v3.5.23. | Power Genius XL Utility v2.2.10.

FLEX-6000 Signature Series

Any discussion related to your FLEX-6000 hardware should be created here. This includes the FLEX-6300, FLEX-6400, FLEX-6400M, FLEX-6500, FLEX-6600, FLEX-6600M and the FLEX-6700. Please note that discussions related to the configuration of a FLEX-6000 would be more appropriately created in one of the Software subcategories.

New Discussion Ask a Question

Discussion	Started By	Replies	Views	Most Recent
6700 Timeout	Greg April 2014	2	14	Tim - W4TME April 2014
Sim31	Steve - M3SXA April 2014	0	1	Steve - M3SXA April 2014
Loss of Network Connection Answered	Bob G W1GLV April 2014	3	1	Bob G W1GLV April 2014
Another new DXCC	Steve - M3SXA April 2014	25	2	Steve - M3SXA April 2014
when does the payment for upgrades for software start again? Answered	James Kennedy-WU5E April 2014	2	1	Greg - K5GJ April 2014
Hardware upgrade capability for 6000 series Answered	Ken - NM9P April 2014	6	1	Ken - NM9P April 2014
What Is Best Way To Use SSDR with Digital Signal Splits Greater Than 10 Khz Answered	W5UN_Dave April 2014	8	1	Jim Hope April 2014
cp210x driver and Smart SDR CAT	Guenter, DK1RI April 2014	3	1	Guenter, DK1RI April 2014
Relay & ALC Expert FA 1K Answered	iz7auh February 2014	1	1	george stiglich April 2014
transmit quits	Drax April 2014	1	2	Tim - W4TME April 2014
Flex6500 GPSDO and FLDIGI are killer FMT app.	Andrew VK5CV September 2013	10	1	Andrew VK5CV April 2014
on the WPX contest in just 9 hours of operating time. The FLEX 6500 worked 214,119 points. good job	James Kennedy-WU5E April 2014	1	1	Ken - NM9P April 2014
Flat line Panadaptor on 40m	G4BIM April 2014	4	2	G4BIM April 2014
CW offset added to Tune frequency in SSB and modulated in AM mode	ai6re April 2014	0	1	ai6re April 2014
lost connection to radio	Steve - M3SXA April 2014	0	1	Steve - M3SXA April 2014
heil Proset ic + AD-1-Y Answered	Steve - M3SXA March 2014	2	2	Steve - M3SXA March 2014
4 meter band uk Answered	Steve - M3SXA March 2014	2	1	Steve - M3SXA March 2014
Such a good looking bit of kit!	Richard G7EIX March 2014	0	1	Richard G7EIX March 2014
6500 10MHz Input Answered	Guenter, DK1RI March 2014	1	2	Tim - W4TME March 2014
radio setup missing	DonS March 2014	8	1	K1UO - Larry March 2014
road map update? Answered	K2CB Eric Dobrowansky March 2014	2	2	Edward Armstrong-WB2K March 2014
PSL1VOC-0.92 Error	Mark - NU6X March 2014	1	1	Tim - W4TME March 2014
Cannot activate the ATU remotely via CAT or any other means Answered	K2CM March 2014	4	1	K2CM March 2014
conducting dust **** out? Question	James Kennedy-WU5E March 2014	0	2	James Kennedy-WU5E March 2014
CAT control for ATU Tuning? Question	K2CM March 2014	0	2	K2CM March 2014
Buttons not working	Dale KB5VE March 2014	5	1	Tim - W4TME March 2014
SmartCat Freq info from multiple slices Question	Harvey Wizbang March 2014	0	1	Harvey Wizbang March 2014
SmartSDR CAT ver1.2.4.0 Port Map	Takeshi Yamada March 2014	2	1	Takeshi Yamada March 2014
How can you tune the frequency second and third digit on the 6500. Thank you W5JI Answered	Joe DiMare March 2014	4	1	James Nelson March 2014
smartsdr cat - How to edit rather than re-enter Answered	Stan VA7NF March 2014	9	1	Ken - NM9P March 2014