Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.

Need the latest SmartSDR or 4O3A Genius Product Software?


SmartSDR v4.0.1 and the SmartSDR v4.0.1 Release Notes

SmartSDR v3.10.15 and the SmartSDR v3.10.15 Release Notes

The latest 4O3A Genius Product Software and Firmware

If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

FLEX Series (Legacy) Radios

This category is for discussions related to the Legacy FLEX Series software defined radios which include the FLEX-5000, FLEX-3000, FLEX-1500 and the original SDR-1000.

New Discussion Ask a Question

Sort Hot ▾

• Hot
• Top
• New

Discussion List

Discussion	Started By	Replies	Views	Most Recent
New (used) Flex 3000 Owner, PowerSDR Install Question Answered	Johnny Twist November 2016	4	2	Tim - W4TME November 2016
MINIDELUXE FLEX 3000 CONFIG FOR DIGITAL MODES Answered	Mark Gottlieb November 2016	3	33	W8TZ Ross November 2016
N2LRB 1500 to KXPA100 Answered	Dave G WS0D October 2016	4	5	Dave G WS0D October 2016
My Power SDR (both 2.7.2 and Darrin's T10) have stopped showing the CPU %, F'heit/Celsius toggle Answered	Peter October 2016	8	5	Larry Williamson October 2016
Connect Flex 1500 to Elecraft KXPA100 amplifier Answered	Jose B Rivera October 2016	8	11	Jose B Rivera October 2016
wanted flex 5radio 1500 uk only please Answered	elan October 2016	2	1	elan October 2016
EXT Bandpass Filters for 6300? Answered	Paul - K6HR September 2016	2	12	EA4GLI September 2016
PowerSDR 2.7.2 ke9ns Revision T9 available for download	KE9NS August 2016	9	160	KE9NS September 2016
Viewing a Flex Radio setup Answered	dan September 2016	2	2	Mike_W7TUS September 2016
Flex 5000a receiver goes off after 20-30 seconds. need to hit stop/start button to revive. Helpful a	Stephen Yacullo September 2016	2	2	Stephen Yacullo September 2016
Ethernet to Firewire adapters Answered	Bob Meadows September 2016	2	2	Tim - W4TME September 2016
PowerSDR 2.7.2 Lower Band Edge Marker Error on 6m Answered	Mick September 2016	11	8	KE9NS September 2016
Looking for help hooking up Flex 3000 to JT65 modes Answered	Larry Williamson September 2016	3	53	Larry Williamson September 2016
Flex 3000 firmware or hardware upgrade needed? Answered	Ted September 2016	1	16	Jay Nation September 2016
Noise Blanker settings on the 3000 Answered	Larry Williamson August 2016	10	16	John August 2016
Real DX Cluster Answered	John August 2016	1	7	Ken - NM9P August 2016
thank you KE9NS	elan August 2016	0	1	elan August 2016
Question(s) Regarding DSP|Options Tab & undocumented function (PowerSDR/Flex 3K) Answered	JDE August 2016	3	25	Jay Nation August 2016
Flex-3000 firewire connection issue cable ?? Answered	Marc Lalonde August 2016	6	2	Jay Nation August 2016
PSDR & SmartSDR CAT Answered	DonS August 2016	12	15	Jay Nation August 2016
Flex 3000 adding an amplifier Answered	David Kutiej November 2015	23	336	Larry Williamson August 2016
flex 3000 manual calibration how? Answered	elan August 2016	3	94	John August 2016
Ghost signal on Flex 3000 Answered	Morris Wideman August 2016	1	2	Ken - NM9P August 2016
Flex 5000a interface with MFJ 998 and Ameritron ALS 600 or 1306 Answered	John Watson W4JCW August 2016	1	33	Jim August 2016
Mike issue on 1500	Tom Stahl August 2016	4	3	Tim - W4TME August 2016
Tool.exe tried to run Answered	John August 2016	15	2	Tim - W4TME August 2016
flex 3000 no much mic drive Answered	elan August 2016	7	3	elan August 2016
I need an elmer for a used flex 1500 I just purchased.	Michael J. Westfield August 2016	2	1	Dudley-WA5QPZ August 2016
wanted flex control /and w2ihy i plus Question	elan August 2016	0	2	elan August 2016
where i can buy new power cable for the flex 3000? Answered	elan August 2016	1	83	K2CM August 2016

New Discussion Ask a Question