Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?

SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

FLEX-6000 Signature Series

Any discussion related to your FLEX-6000 hardware should be created here. This includes the FLEX-6300, FLEX-6400, FLEX-6400M, FLEX-6500, FLEX-6600, FLEX-6600M and the FLEX-6700. Please note that discussions related to the configuration of a FLEX-6000 would be more appropriately created in one of the Software subcategories.
New Discussion Ask a Question

Discussion List

Discussion
Started By
Replies
Views
Most Recent
Screen missing slice and info but showing signals
Dave DaveDave Dave
15
12
Tim - W4TMETim - W4TME
Tune While Using a Waveform
k3Timk3Tim
3
1
WA2SQQWA2SQQ
Rev 1.5.1 and DXLab Commander Issue
Answered
Brad - N6SPMBrad - N6SPM
6
5
James Kennedy-WU5EJames Kennedy-WU5E
FreeDV and VOX operation
Answered
dlwarnbergdlwarnberg
9
13
dlwarnbergdlwarnberg
A real handycap for DXers
JoeJoe
15
1
Mike_N1MDMike_N1MD
Timer built into flex radio
Answered
clint yatesclint yates
7
3
KC2QMA_JohnKC2QMA_John
XVTR signal getting into ANT2???
Question
Roy LauferRoy Laufer
0
1
Roy LauferRoy Laufer
Does anyone use 70cm transverters for FM Repeaters?
Answered
Roy LauferRoy Laufer
27
256
Mark GottliebMark Gottlieb
CWX always transmits
Jim ShafferJim Shaffer
4
1
Eric-KE5DTOEric-KE5DTO
running windows 10 and can get dax drivers to work?
Answered
Don w2xb Don w2xb
27
1
richrich
Is it OK to turn power supply off every time i'm done using my flex6300?
Answered
Mike KD2CJJMike KD2CJJ
3
2
Tim - W4TMETim - W4TME
pc input
Answered
Rich McCabeRich McCabe
3
4
Rich McCabeRich McCabe
Flex 6000 and PR-781 eq settings
Answered
Larry _ NY8TLarry _ NY8T
5
815
k0eook0eoo
CWX+FREQUENCY+OFF but not voice
Mike KD2CJJMike KD2CJJ
3
2
Mike KD2CJJMike KD2CJJ
Can the service dept. run a diagnostic test on my radio over the inet?
Answered
Bill-W9OLBill-W9OL
5
2
Tim - W4TMETim - W4TME
Strange behavior on 160 and 17 meters using WNB
Burch - K4QXXBurch - K4QXX
29
53
Ken - NM9PKen - NM9P
SmartSDR 1.5 and FlDigi 3.23.02
Ed, K0KCEd, K0KC
10
3
Ed, K0KCEd, K0KC
Best way to Doppler Shift the 6500 with satellites
Answered
Jim W3IPOJim W3IPO
9
44
W0DHBW0DHB
Using two 3rd Party programs. Need 2nd com port. How to config?
Answered
James Del PrincipeJames Del Principe
5
13
James Del PrincipeJames Del Principe
Logger 32 with Flex 6500
Answered
James Del PrincipeJames Del Principe
9
390
James Del PrincipeJames Del Principe
DStar on Flex 6300 question about slow data modes ...
Question
Gary L. RobinsonGary L. Robinson
0
11
Gary L. RobinsonGary L. Robinson
Can I create a Profile that is non band specific?
Answered
Bill-W9OLBill-W9OL
3
1
Alan Nusso, N4BVAlan Nusso, N4BV
Profile command failure (?)
Ron ParsonsRon Parsons
1
1
Tim - W4TMETim - W4TME
How to hold a comport
Answered
Bill / VA3QBBill / VA3QB
4
2
Bill / VA3QBBill / VA3QB
Receiver Comparison on 20 meters
Jim W3IPOJim W3IPO
2
3
Jim W3IPOJim W3IPO
Flex 6500 with ALS600
Answered
Tony WV2CTony WV2C
9
52
Tony WV2CTony WV2C
RTTY MODE FLDIGI REV MODE ONLY
Answered
iz7auh iz7auh
3
27
DH2IDDH2ID
rtty audio problem
Answered
jimjim
5
2
km9r.mikekm9r.mike
unsubsribing
Answered
Robert AllbrightRobert Allbright
5
2
SikkRikk StevensSikkRikk Stevens
How to configure transverters for 6700 FDX satellite operation?
Answered
Bob N7ZOBob N7ZO
2
4
pa0biepa0bie
New Discussion Ask a Question

Categories

Popular Tags