Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
N1MM Leading Numbers T
Options
Terry K8EET
Member ✭✭
Anyone know why cannot get N1MM to send Cut Numbers (T instead of Zeros) I have enabled Cut Number Style. I have checked "Send Cut Numbers" and tried checking and unchecking the checkbox for "Sending Leading Zeros" (?)
0
Answers
-
Mike-VA3MW Administrator, FlexRadio Employee, Community Manager, Super Elmer, Moderator adminOptionsI'm sure you have seen this ... just in case
https://n1mmwp.hamdocs.com/setup/the-configurer/- Send leading zeros in serial numbers – Serial numbers, which are sent either using the # macro or the {EXCH} macro (if the Sent Exchange box in the Contest Setup contains 001), may be sent either with or without leading zeros (e.g. 003 or just 3), depending on whether this option is checked or not. In CW, the “cut numbers” option can be used to send the leading zeros as T or O instead of 0. The leading zeros option does not affect numbers other than serial numbers
- Send cut numbers – In CW this causes serial numbers, and RSTs if you are using the {SENTRSTCUT} macro, to be sent using the Cut Number Style set at the bottom of the dialog. Ctrl+G can be used to toggle this option while operating. The new status after toggling will be shown in the status line at the bottom of the entry window. Numbers other than serial numbers and {SENTRSTCUT} will not be affected by this option. The cut numbers option does not apply to SSB or digital modes
0 -
Mike, Thanks for the quick response. Perhaps, cut numbers only works with {SENTRSTCUT} which are not used in the QSO parties. I guess I have a work around by putting a TT# in the exchange. I'll just remove one T when I get to 10 and the other one when/if I get to 100. Only mildly inconvenient. I thought this worked in previous QSO Parties.0
-
Terry, I use the "send leading zeros" option and "send cut numbers" checked in the Config>Function Keys section. When I exceed ten I remove the "send leading zeros" check. I use the "#" for the exchange. It's pretty fast this way, too.
John
0 -
Thanks John, Yes I came to the conclusion that was what I was going to have to do and it isn't that difficult. I was banging my head against the wall thinking that there must be a more straightforward way to do it. (Maybe there is)
Thanks for your comments,
73 Terry
K8EET
0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software