Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR or 4O3A Genius Product Software?
SmartSDR v4.1.5 | SmartSDR v4.1.5 Release Notes
SmartSDR v3.10.15 | SmartSDR v3.10.15 Release Notes
The latest 4O3A Genius Product Software and Firmware
SmartSDR v4.1.5 | SmartSDR v4.1.5 Release Notes
SmartSDR v3.10.15 | SmartSDR v3.10.15 Release Notes
The latest 4O3A Genius Product Software and Firmware
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Best Of
-
Re: How to track frequency using CAT from a Mac running SmartSDR for Mac to a PC running NMM?
Hi Randy Just run SmartSDR CAT on the PC with N1MM and have it connect to the radio. Next, using SmartSDR CAT, add a Serial Port for N1MM and have N1MM connect to that serial port. Unlike other radio…1 -
Re: How to track frequency using CAT from a Mac running SmartSDR for Mac to a PC running NMM?
Hi Mike, I am running remote. When running SmartSDR CAT on a PC, does each computer have its own configuration for CAT? Please confirm this is correct. When I operate locally to the radio and load Sm…1 -
Re: How to track frequency using CAT from a Mac running SmartSDR for Mac to a PC running NMM?
Yes, SSDR CAT settings are stored on the PC that is running SSDR CAT. To talk to N1MM, SSDR CAT must run on the same PC that N1MM is running on. If you wish to run N1MM on the remote PC, than SSDR CA…1 -
Re: WSJT-X / JTDX stops sending TX Audio to the Radio after sitting idle for a while.
"disable the Nvidia card" and "high performance which disables CPU hibernate and sleep" I second both of these steps!1 -
Re: WSJT-X / JTDX stops sending TX Audio to the Radio after sitting idle for a while.
One thing I found is to disable the Nvidia card under sound devices in Device Mangler. Having a “sound device “ (monitors) that go into sleep mode can cause grief with Windoze device enumeration. I a…1 -
Re: Troubleshooting help Flex3000 suggestions needed
Hi AA4TE... sorry, I don't own a 3000, but maybe try some of the things we recommend to people with 6000's??? a) Try a 'factory-reset' and see if that restores transmit? b) Try co…1 -
Re: Winlink and VARA HF
This thread on the Flex groups.io group, especially near the bottom, has lots of answers. I can’t find the discussion of VARA and latency that used to be here. Just set digital latency as low as poss…1 -
Re: Antenna Genius Control
Use PG XL 3.8.4 (or newer) and TG XL 1.1.20 or 1.2.11 (or newer 1.2.x). In TG XL under Genius Integration tab check PG XL and enter IP of PG XL. Enable Band A only (if using port A, otherwise Band B …1 -
Re: Flex 6400M and Electro Voice RE320
I have been using an RE320 with my 6500 for some years. No pre-amp needed, and I get plenty of output and great signal reports. Perhaps you don't have the connections correct. The RE320 is balan…1 -
Re: Font install wiped out every reboot
I figured it out. The font was being installed only for my user and for some reason only for that session. I followed the instructions here and installed it for all users and now it stays between reb…2
