Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Suddenly no reception on antenna one and no transmit on either, infinite SWR on TX
Options
Russ Locke
Member ✭✭
Suddenly I had no reception on antenna 1. I switched my antenna (I only have one) to antenna 2 and now I had RX. BUT when I hit the Tune function, the SWR's went off the chart and I had to shut down the radio. I rebooted it and then tried to Xmit on antenna 2. SWR's off the chart again. No signal at all when I attach my antenna to Antenna 1. I had not disconnected the antenna at the pass through, this just came out of the blue. Any ideas?
The radio is a 6300 and the software is latest, 2.4.9.
The radio is a 6300 and the software is latest, 2.4.9.
0
Comments
-
Mike-VA3MW Administrator, FlexRadio Employee, Community Manager, Super Elmer, Moderator adminOptionsHi Russ
A few things.
First, can you check the antenna with another device like an analyzer or another radio?
Can you do an SWR test to a dummy load?
If you don't have any of the above, then I would export your profiles to save your settings and then do a radio reset. And then, test again.
If that doesn't work and you have confirmed the antenna and all jumper cables are ok, then it would be time to open a support ticket.
Mike
0 -
For the receive part it could be a blown ESD diode but I don't think that affects TX.0
-
I had some RX weirdness like this earlier in the week, Saved my profiles, did a reset and everything was good.
Zack N8FNR0 -
I found the problem, mostly operator error (the first place to look.....) Thanks for the suggestions.
0 -
Details, please.0
-
I have a similar problem. Could you share your solution?
Frank Smith, WS1MH
0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 328 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 810 Third-Party Software