SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
ATU Command, How to Structure?
I am not clear on how to use the "atu start" and the "atu bypass" API commands.
The wiki shows the command structure as "<pre>C14|atu start</pre>", and explains, "there must be a slice designated as the transmitter and the radio transmit state must be READY".
The question is, how can I structure a command to use the Flex internal ATU?
Below is a log of my attempt, but as you can see, it failed.
Alan. WA9WUD
=================
Radio[1]._sendRequest(C5|atu start)
Radio[1]._receiveMessage(R5|0|)
Radio[1]._receiveMessage(S0|interlock tx_client_handle=0x00000000 state=NOT_READY reason= source= tx_allowed=0 amplifier=)
Radio[1]._receiveMessage(S0|interlock tx_client_handle=0x00000000 state=READY reason= source= tx_allowed=1 amplifier=)
Radio[1]._receiveMessage(S516A56AE|interlock acc_txreq_enable=0 rca_txreq_enable=1 acc_tx_enabled=0 tx1_enabled=1 tx2_enabled=0 tx3_enabled=0 tx_delay=30 acc_tx_delay=0 tx1_delay=0 tx2_delay=0 tx3_delay=0 acc_txreq_polarity=0 rca_txreq_polarity=0 timeout=300000)
Radio[1]._receiveMessage(S0|interlock tx_client_handle=0x62F85ACA state=NOT_READY reason= source= tx_allowed=0 amplifier=)
Radio[1]._receiveMessage(S516A56AE|interlock acc_txreq_enable=0 rca_txreq_enable=1 acc_tx_enabled=0 tx1_enabled=1 tx2_enabled=0 tx3_enabled=0 tx_delay=30 acc_tx_delay=0 tx1_delay=0 tx2_delay=0 tx3_delay=0 acc_txreq_polarity=0 rca_txreq_polarity=0 timeout=300000)
Radio[1]._receiveMessage(M31000003|Interlock is preventing transmission)
Radio[1]._receiveMessage(M31000003|Interlock is preventing transmission)
Radio[1]._receiveMessage(S0|interlock tx_client_handle=0x00000000 state=READY reason= source= tx_allowed=1 amplifier=)
Radio[1]._receiveMessage(S0|interlock tx_client_handle=0x00000000 state=READY reason= source= tx_allowed=1 amplifier=)
Best Answer
-
dahhh!
Thanks, Dave, WO2X, for the memory jog.
I was MultiFlex, two clients, and did not include a bind client command along with the "atu start" command.
All is good now.
Alan. WA9WUD
0
Leave a Comment
Categories
- All Categories
- 247 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.4K Software
- 5.9K SmartSDR for Windows
- 135 SmartSDR for Maestro and M models
- 330 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 344 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 771 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 727 Genius Products
- 391 Power Genius XL Amplifier
- 252 Tuner Genius XL
- 84 Antenna Genius
- 224 Shack Infrastructure
- 151 Networking
- 371 Remote Operation (SmartLink)
- 118 Contesting
- 583 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 810 Third-Party Software