Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
LOG40M2 setup with FLE6400
Options
tpetruzzellis
Member ✭✭
Greetings:
Can anyone help with new logging program setup.
I am trying to setup LOG40M2 with my Flex6400 transceiver.
I cannot seem to to get the radio frequency to display on the logger screen.
The Log40M2 program gives hamlib or omnirig as options, but don't know if those are actually needed. Should the FlexCat be setup for TCP or serial.
Anyone familiar with this software and setup?
Any help would be greatly appreciated.
Thanks
Tom
0
Best Answer
-
Tom, I just went through the same thing with my 6500 and Log4OM this past week.
Make sure that you are using the version 1.19 of Omnirig that works with Log4OM (the latest version won't work with Log4OM)
Set up your CAT port on an unused virtual serial port
Install and run Omnirig as administrator on Windows
Run wstj-x and JTalert and Log4OM as administrator
I kept getting "offline" displayed on Log4OM until I went back and made sure these things were done.
Good luck!0
Answers
-
I will be running up against this issue within a couple of days. I run Log4OM V2 and CAT using OmniRig between my Orion 2 & TS-890 without issue. My understanding is that the 6600M with talk back & forth with Log4OM via OmniRig using the Kenwood protocol.0
-
YEs, I have heard that omnirig will work with a Flex 6000 series transceiver using the Kenwood settings. It does have SmartSDR built into it's settings though.0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software