Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR or 4O3A Genius Product Software?

SmartSDR v3.9.19 and the SmartSDR v3.9.19 Release Notes
SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes

The latest 4O3A Genius Product Software and Firmware
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

No reception on 6500

Member ✭✭
in FLEX-6000 Signature Series
What is wrong? was doing CW on 20m (remote) good reception but very high audio tone. radio rebooted in an attempt to restore the audio tone. But no more receiving any signal at any band (steppir DB42 connected) Started smart sdr on PC at radio side with teamvieuwer, same there so i guess hardware have serveral antenna's , all the same not a beep.

Welcome!

It looks like you're new here. Sign in or register to get started.
Sign In
Register

Best Answers

  • Member, Super Elmer Moderator
    Answer ✓

    Hi Jan, I know that you are remote, but if you can get to your radio site, try moving the antenna to ANT2. If that works but ANT1 does not work, then it sounds like a hardware problem with ANT1.

    Another thing to look at is the connections and cabling between the radio and antenna. You could try temporarily moving the antenna to RXA to be sure that the antenna and cabling are OK.

  • Administrator, FlexRadio Employee, Community Manager, Super Elmer, Moderator admin
    Answer ✓

    @Jan on8aj Can you include a screen shot of SmartSDR please. It really helps to diagnose your situation.


    73

  • Member ✭✭
    Answer ✓
    How do i reset the radio, i have only control over the 12v dc power supply and the remote on/off on the back of the radio. If i need to go and puch some buttons manually, i'll drive there tomorrow.
    Thanks Jan

Answers

  • Member ✭✭
    Can't edit my own post... I can receive on my RX antenne , ant 1 no TX en no RX, ant 2 is not connected, trnsverter is working in TX & RX
  • Member ✭✭
    edited April 2021
    This is screenshot, i already downgraded to 3.1.12 but no change so back at 3.2.31 now, this is picture with antenna 1 ( display collor set to black)
  • Administrator, FlexRadio Employee, Community Manager, Super Elmer, Moderator admin

    Thanks!

    Can you try 1 more thing. Please export your profiles and do a database reset on the radio and then see if it works as you expect.

    Let me know.

    73

  • Member ✭✭
    I have only control over the 12v power suply (on/off) and the rear on/off switch. If i need to push some buttons manually i drive there tomorrow. Thanks for the help!
  • Member ✭✭
    edited April 2021 
    Been to the remote lacation. 
Pressed OK button and power on until the white light came on. Let the radio start up, no difference. 
Changed antenna from ouput 1 to output 2, no difference either. Hooked up my icom ans searched for a strong signal, 
found 9a station on 14.254 with 59+ signal. Antenna back to the flex, VFO to 14.254 but noting, no reception at all. 
Also no power, not on antenna A and not on B (photo taken on RX ant)
    image.png


  • Administrator, FlexRadio Employee, Community Manager, Super Elmer, Moderator admin

    I have opened a support ticket for you

This discussion has been closed.

Welcome!

It looks like you're new here. Sign in or register to get started.
Sign In
Register

Quick Links

Categories