Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
WSJT-X Multi Band Operation
Options
Dan KG0AQ
Member ✭✭
My last post ended up unsolved and went in a slightly different direction as it may just be an operational issue inherent to multi band use. I just want to confirm the following operation before troubleshooting further.I am using JTAlert with WSJT-X. I have also turned off all 3rd party programs.
If you have the "Call 1st" box unchecked and the "double click on call sets Tx enable" unchecked in WSJT-X then you double click on a call does your transmit flag in SmartSDR move to the correct band/window with multiple instances of WSJT-X open? I just want the TX to be ready in case I want to work the station. I thought this was my previous behavior but I could be wrong? If I click on the Enable TX button in WSJT-X the transmit flag DOES move to the correct band. But the obvious problem with this is timing for band and antenna switching/tuning. On 20-6 meters this is not a problem because of my hexbeam. It is an issue on 30-160 though. I use a 6400 with a Palstar AT-Auto and CX-Auto for antenna switching. TIA! 73
Dan KG0AQ
If you have the "Call 1st" box unchecked and the "double click on call sets Tx enable" unchecked in WSJT-X then you double click on a call does your transmit flag in SmartSDR move to the correct band/window with multiple instances of WSJT-X open? I just want the TX to be ready in case I want to work the station. I thought this was my previous behavior but I could be wrong? If I click on the Enable TX button in WSJT-X the transmit flag DOES move to the correct band. But the obvious problem with this is timing for band and antenna switching/tuning. On 20-6 meters this is not a problem because of my hexbeam. It is an issue on 30-160 though. I use a 6400 with a Palstar AT-Auto and CX-Auto for antenna switching. TIA! 73
Dan KG0AQ
0
Answers
-
The Call 1st check box has no bearing on this. If you have your different instances setup properly, when you TX WSJT will use the proper slice to TX (and the TX follows). I am running 3 instances right now and it seamlessly follows to the proper Slice.
And I have a KPA500 and KAT500 connected via the USB ports and they too will follow to the proper band/antenna.0 -
Yes, I stated "If I click on the Enable TX button in WSJT-X the transmit flag DOES move to the correct band." But I want to know if the transmit flag will follow when double clicking to receive only.
NO transmit until I select the "Enable transmit" button manually.0 -
When TX is set by WSJT then the appropriate Slice will go into TX. If the TX command is not sent to the Flex then it has no idea which slice to TX on. Just trying to help out but am getting confused by your statements.0
-
I never use the automated transmit features of WSJT-X. Only during the actual QSO. I like to receive the station and find a open frequency to transmit then i press the TX enable button. I thought I once had the transmit flag in place BEFORE I pushed the TX button in previous versions of WSJT-X.. I guess this is NOT the way the program and radio work together? It would be nice for me to have the TX flag set in the correct window before I hit the transmit enable button. Thanks for clarification of your system. 73
Dan KG0AQ0 -
I also keep the TX Enable button off until I find a station I want to work.0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 489 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 223 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software