Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
How do I send band data to an Ameritron RCS-12
Steven WA8Y
Member ✭✭
When I bought my 6600 I also ordered a FTDI Chip cable that was suppoed to output BCD band data. Part number C232HM to MPSSE Serial cable. I plugged the USB end into the 6600, I wired the GPiO; 0, 1, 2, 3, Vcc, GND to some LEDs. All GPiO are logic zero on all bands except for 20m where all outputs are logic One. How can send band data from my 6600 to the Ameritron RCS-12? The RCS-12 manual only illustrates Yaesu, Kenwood, and Icom. Yaesu does it thru BCD. I am sending band data to my amp via a USB-Null modem- USB Cable. The amp is looking for band data from a Kenwood TS-50. So the Flex looks like a Kenwood.
0
Answers
-
I believe that is the wrong cable. You want the C232HM-EDHSL-0 USB to bit cable. https://www.mouser.com/ProductDetail/FTDI/C232HM-EDHSL-0/?qs=EB8w3yL7SqPZGmdI8JhrMA==&gclid=CjwKCAiAz7TfBRAKEiwAz8fKOMNLsLfOa9RmjYXNmqFtOZlhGnbFCCjtmOcbcQXdWSdiePZ0_GB8UhoCpWsQAvD_BwE Or an easier solution is what I use. The SainSmart USB-8 board which I use to drive a W2IHY 1x4 antenna switch. https://www.amazon.com/SainSmart-Eight-Channel-Relay-Automation/dp/B0093Y89DE It can be driven by the Flex Or DDUtil. Dave wo2x1
-
Thank you so much for your answer. I ordered both.
Can I call you if I have questions?
0 -
Yes. Email me at Wo2x at ARRL dot net and I’ll pass along my number. The USB-8 might be the easiest solution of the two. Dave wo2x0
-
I use Flex 6500 with Ameritron RCS-12.
The correct cable to have Yaesu BCD information is the "C232HM-EDHSL-0 USB".
I ordered it from Mouser and everything worked flawlessly.
0
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 746 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software