Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Dual antenna connection
Options
Sergey KN7K
Member ✭✭✭
I run a new coax from 6el 5m antenna and connected it to Ant2.
Ant1 is a 2el Steppir connected through Microham Power meter.
I was suprised to see that when I TX on Ant2 50mhz antenna, my power meter (that connected to Ant1) shows 0.011w and SWR 8.47.
Any idea why I would see SWR reading from Ant 1 when I transmitting to Ant 2?
No other panadapters/slices active at that time, only slice A.
Thanks
Sergey, KN7K
Ant1 is a 2el Steppir connected through Microham Power meter.
I was suprised to see that when I TX on Ant2 50mhz antenna, my power meter (that connected to Ant1) shows 0.011w and SWR 8.47.
Any idea why I would see SWR reading from Ant 1 when I transmitting to Ant 2?
No other panadapters/slices active at that time, only slice A.
Thanks
Sergey, KN7K
0
Answers
-
Sounds like you have reflected power coming back from Ant1 and it’s feedline into the SWR meter and there’s no output power on Ant2; hence, high SWR ratio of reflected vs forward power.0
-
It seems like the case. Antennas about 3ft apart on small tower. It is not a problem yet as I am running 100w for now. Interesting to see what will be the reading when I will have an amp.
Sergey, KN7K0 -
The antenna inputs have 70db isolation. but in some cases when antennas are to close as said by Paul it is common to use a band pass filter for even more isolation when using an amp.0
-
Any recommendation for a band pass filters?
Thanks
Sergey, KN7K0 -
Paul,
Thanks you for suggestion.
Will have to check how does it look at higher power.
Currently I just tested on 50mhz antenna with 100w from flex 6600.
Next thing to try to TX on 1.8-28mhz with Acom 2000a and see how it will impact the 50mhz.
If it will be an issue than will consider the filters.
Sergey, KN7K0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 489 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 223 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software