Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
The latest SmartSDR Software:
SmartSDR v4.2.20 | SmartSDR v4.2.20 Release Notes
SmartSDR v3.10.15 | SmartSDR v3.10.15 Release Notes

The latest 4O3A Genius Product Software:
The latest 4O3A Genius Product Software and Firmware
How to Receive Technical Support::
If you are needing assistance with FlexRadio products, please refer to the product documentation or check the Help Center for known solutions. Need technical support from FlexRadio? It's as simple as creating a HelpDesk ticket.

wsjt x rc2 won't transmit

Options
W5XZ - dan
W5XZ - dan Member ✭✭
edited June 2019 in FLEX-6000 Signature Series
rc 1 worked fine

Answers

  • W5XZ - dan
    W5XZ - dan Member ✭✭
    edited June 2019
    Options
    have i hosed up the dax channels, or what?

    ver 1.8, rc-1 worked great with FT 8..

  • W5XZ - dan
    W5XZ - dan Member ✭✭
    edited June 2019
    Options
    connecting normally,  by dxLabs Commander...
  • N6OIL
    N6OIL Member ✭✭
    edited June 2019
    Options
    Maybe your transmit bandwidth is too narrow? Mine is at Low Cut 200 High Cut 2500
  • W5XZ - dan
    W5XZ - dan Member ✭✭
    edited September 2017
    Options
    thanks, but thats not it...ptt won't even enable..

  • W5XZ - dan
    W5XZ - dan Member ✭✭
    edited September 2017
    Options
    it's decoding very well, on 160m...but tune button does not put the rig in tx..
     much less transmit

    config / settings / audio shows

    input: dax audio rx 1 (FRS DAX audio )
    output: dax audio tx (FRS system dax tx)

    radio tab is Dx Lab Suite commander, which is working normally on other
     modes...

    have shut down and re-started wsjt x 1.8 rc-2 several times...

    has Murphy moved in??? again ????

    73, w5xz, dan, top band sick-o..


  • Ned K1NJ
    Ned K1NJ Member ✭✭
    edited September 2017
    Options
    Works OK here.  Using CAT for keying.  CAT in RC2 settings.  P COM9 in SSDR
    CAT as ptt,

                 Ned, K1NJ
  • W5XZ - dan
    W5XZ - dan Member ✭✭
    edited September 2017
    Options
    with dxLabs Commander?  what am i missing?

  • Dan -- KC4GO
    Dan -- KC4GO Member ✭✭
    edited March 2018
    Options
    Only software needed WSJT-X - RC2 and FLEX CAT, DAX, SSDR... Check your CAT and DAX settings. Works fine here.  I found that when I upgraded to rc2 it lost my CAT settings and in DAX had to go recheck the TX box. Also under the Frequency tab had to do a refresh.  A 
  • WA2SQQ
    WA2SQQ Member ✭✭
    edited September 2017
    Options
    Working here since released
  • WA2SQQ
    WA2SQQ Member ✭✭
    edited September 2017
    Options
    Did you follow the instructions and reset the frequency tab, in settings?
  • Tim - W4TME
    Tim - W4TME Administrator, FlexRadio Employee admin
    edited September 2017
    Options
    CAT is what enables rig control (keying), not DAX.  Sounds like DAX is working.
  • W5XZ - dan
    W5XZ - dan Member ✭✭
    edited June 2019
    Options
    thanks, guys. found the issue. setttings / radio ptt method...switched from vox to cat, and all is well now...

    what a remarkable mode !  73, w5xz, dan

  • W5XZ - dan
    W5XZ - dan Member ✭✭
    edited September 2017
    Options
    yes

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.

Comment As ...

Categories