Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Drive level meter question
Options
DrTeeth
Member ✭✭
The drive level meter has a long bar with a separate rectangle to the right of it. I can increase my drive (digital modes using DAX) so that the rectangle goes into the red of the scale but remains yellow. Is that a Bad Thing © or does the distortion start when the rectangle itself turns red?
OT: Ping FRS. It is very difficult to fine tune settings in DAX using the mouse, and for some reason, keyboard control is not enabled. Need finer control as a unit or two change up or down on the TX gain has a significant effect on the output.
OT: Ping FRS. It is very difficult to fine tune settings in DAX using the mouse, and for some reason, keyboard control is not enabled. Need finer control as a unit or two change up or down on the TX gain has a significant effect on the output.
0
Answers
-
Keep the peak square on the audio input meter from going into the red area at all, not just the bar. Also, use DIGIU or DIGIL so it bypasses the processing and shallows the filters to reduce latency.0
-
What I am trying to establish is whether the distortion starts when the peak square goes into the red area or when it actually changes colour to red itself? It's not clear. To me the latter is more logical, viz keep the peak yellow.
0 -
Yes keep the peak square in the yellow. I was told this by Steve when I was recording my WinLink demo video.
0 -
So what does the peak square turning red signify? I am labouring the point as in SSDR, it is quite difficult to make small precision movements with the sliders, especially where the use of the cursor keys have not been enabled.
0 -
Place your cursor at the end of the slider in the direction you want to move, then left click. That will move the slider one unit per click.2
-
Robert, Mni tnx for that tip. I am at work at the moment and cannot wait to test it. I hope it works in the DAX control panel too.
Update:- Works in DAX control panel. I wish I could like your tip twice, hi hi.
0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 221 Shack Infrastructure
- 149 Networking
- 369 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 809 Third-Party Software