Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR or 4O3A Genius Product Software?
SmartSDR v3.9.19 and the SmartSDR v3.9.19 Release Notes
SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
The latest 4O3A Genius Product Software and Firmware
SmartSDR v3.9.19 and the SmartSDR v3.9.19 Release Notes
SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
The latest 4O3A Genius Product Software and Firmware
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Drive level meter question
Options
DrTeeth
Member ✭✭
The drive level meter has a long bar with a separate rectangle to the right of it. I can increase my drive (digital modes using DAX) so that the rectangle goes into the red of the scale but remains yellow. Is that a Bad Thing © or does the distortion start when the rectangle itself turns red?
OT: Ping FRS. It is very difficult to fine tune settings in DAX using the mouse, and for some reason, keyboard control is not enabled. Need finer control as a unit or two change up or down on the TX gain has a significant effect on the output.
OT: Ping FRS. It is very difficult to fine tune settings in DAX using the mouse, and for some reason, keyboard control is not enabled. Need finer control as a unit or two change up or down on the TX gain has a significant effect on the output.
0
Answers
-
Keep the peak square on the audio input meter from going into the red area at all, not just the bar. Also, use DIGIU or DIGIL so it bypasses the processing and shallows the filters to reduce latency.0
-
What I am trying to establish is whether the distortion starts when the peak square goes into the red area or when it actually changes colour to red itself? It's not clear. To me the latter is more logical, viz keep the peak yellow.
0 -
Yes keep the peak square in the yellow. I was told this by Steve when I was recording my WinLink demo video.
0 -
So what does the peak square turning red signify? I am labouring the point as in SSDR, it is quite difficult to make small precision movements with the sliders, especially where the use of the cursor keys have not been enabled.
0 -
Place your cursor at the end of the slider in the direction you want to move, then left click. That will move the slider one unit per click.2
-
Robert, Mni tnx for that tip. I am at work at the moment and cannot wait to test it. I hope it works in the DAX control panel too.
Update:- Works in DAX control panel. I wish I could like your tip twice, hi hi.
0
Leave a Comment
Categories
- All Categories
- 332 Community Topics
- 2.1K New Ideas
- 599 The Flea Market
- 7.9K Software
- 6.2K SmartSDR for Windows
- 168 SmartSDR for Maestro and M models
- 398 SmartSDR for Mac
- 262 SmartSDR for iOS
- 247 SmartSDR CAT
- 181 DAX
- 370 SmartSDR API
- 9.1K Radios and Accessories
- 16 Aurora
- 167 FLEX-8000 Signature Series
- 7.1K FLEX-6000 Signature Series
- 912 Maestro
- 52 FlexControl
- 854 FLEX Series (Legacy) Radios
- 873 Genius Products
- 446 Power Genius XL Amplifier
- 312 Tuner Genius XL
- 115 Antenna Genius
- 278 Shack Infrastructure
- 196 Networking
- 440 Remote Operation (SmartLink)
- 135 Contesting
- 727 Peripherals & Station Integration
- 137 Amateur Radio Interests
- 948 Third-Party Software