Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.3.29 and the SmartSDR v3.3.29 Release Notes | SmartSDR v2.7.6 and the SmartSDR v2.7.6 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.6.24 and the Power Genius XL Release Notes v3.6.24
Tuner Genius XL Utility v1.1.8 and the Tuner Genius XL Release Notes v1.1.8
SmartSDR v3.3.29 and the SmartSDR v3.3.29 Release Notes | SmartSDR v2.7.6 and the SmartSDR v2.7.6 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.6.24 and the Power Genius XL Release Notes v3.6.24
Tuner Genius XL Utility v1.1.8 and the Tuner Genius XL Release Notes v1.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
on start up spectrum has a pattern of up and down peaks
N4AB
Old GuyMember ✭✭
6700 with GPSDO using Win 7 On start up I sometime get a spectrum that I don't know what it is or even know how to describe. It starts with a normal spectrum an slowly changes to this up and down peak and valley spectrum, 10 to 12 db swing and every 15 kHz (on 20 meter band). It lasts for 5 minutes to 30 minutes ( if I don't restart SmartSDR ) then slowly goes away. If I do a re-start, most of the time it "cures" the problem and everything is fine for the rest of the day. It does not happen every time but enough that it is a problem. This morning it lasted a little over 30 minutes and I was able to get a screen shot of the spectrum. Now if I can figure out how to send the picture.
I hope this works. Tnx Al N4AB
0
Comments
-
Does it stay the same if you change bands? Do you have antenna attached?0
-
This looks like what I see on 160 meters which I traced to my cable modem. With my Flex-5000, I had to power-down the modem to make contacts, but I just realized that I cannot do that with the 6700 unless I make a direct connection to the computer rather than running it over the LAN. Let me think about this...maybe the LAN will work without an Internet connection if I just leave the router on.0
-
Yes, I have the antenna switched on at the external antenna switch, it is usually grounded but when I get this problem the antenna has been active. And the problem also follows band changing by using the band switch or by just entering a new frequency/band on the slice control panel. Tnx Al N4AB0
Leave a Comment
Categories
- 18.3K All Categories
- 125 Community Topics
- 2K New Ideas
- 274 The Flea Market
- 6.1K Software
- 5.3K SmartSDR for Windows
- 90 SmartSDR for Maestro and M models
- 201 SmartSDR for Mac
- 185 SmartSDR for iOS
- 179 SmartSDR CAT
- 108 DAX
- 316 SmartSDR API
- 7.8K Radios and Accessories
- 6.3K FLEX-6000 Signature Series
- 625 Maestro
- 29 FlexControl
- 768 FLEX Series (Legacy) Radios
- 393 Genius Products
- 235 Power Genius XL Amplifier
- 140 Tuner Genius XL
- 18 Antenna Genius
- 114 Shack Infrastructure
- 71 Networking
- 196 Remote Operation (SmartLink)
- 87 Contesting
- 290 Peripherals & Station Integration
- 86 Amateur Radio Interests
- 567 Third-Party Software