Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR or 4O3A Genius Product Software?
SmartSDR v3.10.15 and the SmartSDR v3.10.15 Release Notes
The latest 4O3A Genius Product Software and Firmware
SmartSDR v3.10.15 and the SmartSDR v3.10.15 Release Notes
The latest 4O3A Genius Product Software and Firmware
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Once again the DAX driver cannot be installed
Laptop Win10
11th Gen Intel(R) Core(TM) i7-1185G7 @ 3.00GHz 3.00 GHz
64-Bit-Betriebssystem, x64-basierter Prozessor
SSDR 3.2.9
Flex6600
The problems with the graphics could be quickly replaced by the driver, so the waterfall diagram runs again :-)
Now I have already experienced a lot with Flex. But that the DAX drivers are not installed at all and I have been trying for 3 days with the help of the forum to remedy it makes me insane.
Now the idea of creating a ticket is not far away. But now I think that will interest some.
SDR starts normally and then knows me after starting DAX that the drivers are not installed correctly. Everyone knows the error picture :-)
Nothing is installed on the PC except the Win10 original installation, no additional programs.
I have executed umpteen times the uninstalled and installed instructions with the .bat files, unfortunately without success. there is no virus program running, the firewall is also off.
Nobody has reported about this kind of error yet, I'm curious if someone can help me.
11th Gen Intel(R) Core(TM) i7-1185G7 @ 3.00GHz 3.00 GHz
64-Bit-Betriebssystem, x64-basierter Prozessor
SSDR 3.2.9
Flex6600
The problems with the graphics could be quickly replaced by the driver, so the waterfall diagram runs again :-)
Now I have already experienced a lot with Flex. But that the DAX drivers are not installed at all and I have been trying for 3 days with the help of the forum to remedy it makes me insane.
Now the idea of creating a ticket is not far away. But now I think that will interest some.
SDR starts normally and then knows me after starting DAX that the drivers are not installed correctly. Everyone knows the error picture :-)
Nothing is installed on the PC except the Win10 original installation, no additional programs.
I have executed umpteen times the uninstalled and installed instructions with the .bat files, unfortunately without success. there is no virus program running, the firewall is also off.
Nobody has reported about this kind of error yet, I'm curious if someone can help me.
0
Comments
Leave a Comment
Categories
- All Categories
- 354 Community Topics
- 2.1K New Ideas
- 618 The Flea Market
- 8K Software
- 3 SmartSDR+
- 6.3K SmartSDR for Windows
- 175 SmartSDR for Maestro and M models
- 413 SmartSDR for Mac
- 267 SmartSDR for iOS
- 252 SmartSDR CAT
- 188 DAX
- 377 SmartSDR API
- 9.2K Radios and Accessories
- 25 Aurora
- 218 FLEX-8000 Signature Series
- 7.1K FLEX-6000 Signature Series
- 923 Maestro
- 53 FlexControl
- 861 FLEX Series (Legacy) Radios
- 897 Genius Products
- 456 Power Genius XL Amplifier
- 325 Tuner Genius XL
- 116 Antenna Genius
- 286 Shack Infrastructure
- 201 Networking
- 445 Remote Operation (SmartLink)
- 141 Contesting
- 759 Peripherals & Station Integration
- 139 Amateur Radio Interests
- 979 Third-Party Software