Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
no TX from WSJT-X FT8
Options
Comments
-
I went to the AppData Local WSJT-x folder and do not see an wsjt-x ini file.. Is it within another folder in that file?0
-
Hello Everyone,
I have had the FLEX 6400 and 6300 for years and this is the first time I am having this problem after making thousands of contacts. It just started recently...When transmitting, I will hear the USB disconnection sound in the computer. The radio continues to transmit but on the next "over" the radio will switch into TX but there will be no RF transmitted. I tried the USB solution and expanded all of the Universal Serial Bus controllers to make sure Power Management was not turning them off to save energy. I also changed my Power Settings in Hardware and Sound which was another solution I found in this forum. All to no avail. I restart WSJT and it will work for one transmit and then go dead. All the time, I am hearing the USB disconnection sound in the computer when this happened. As stated by others, it seems that there is a virtual USB port being used here with the software. Of course, the FLEX radio is connected directly via ethernet cable to the computer. This is not a network connection. I would rather avoid swiping the drive and starting from scratch but I have been there and done that before. Does anyone have any suggestions?
73
Mark
KK2l0 -
It's not a ground system issue, corrosion or break, allowing RF to affect the computer? I mention this because I was getting the USB disconnection ping and found one of my connections to the ground buss had come adrift.
0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 221 Shack Infrastructure
- 149 Networking
- 369 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 809 Third-Party Software