Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.8.19 and the SmartSDR v3.8.19 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.8.19 and the SmartSDR v3.8.19 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Skimmer tunes in 100 Hz steps
Barry GM3YEH
Member ✭✭
FLEX 6500 with SSDR and SDR Bridge to CW Skimmer. Everything perfect except that the tuning steps on CW Skimmer are stuck at 100 Hz which is a bit coarser than I would like. Tuning steps in SSDR are fine. As I tune around with my FlexControl SSDR tunes smoothly but CW Skimmer 'jumps' in 100 Hz steps. Have looked at all SSDR, SDR Bridge and CW Skimmer settings with no luck so far. Any suggestions?
73 Barry GM3YEH
0
Answers
-
Hi Barry,
That is a known issue in CW Skimmer. CWS synchs up every 100 HZ. A workaround (shaking the panadapter) is on page 18 of my "quickstart" notes on the SDR-Bridge web page. You can also click tune the particular call in the skimmer waterfall to synch it up with SSDR.
Alex (author of CWS) is aware of the issue and should address it eventually. (no timeframe though)
Regards, Al / NN4ZZ
al (at) nn4zz (dot) com0 -
Thanks Al. I've picked up a copy of your notes on SDR-Bridge now.
73 Barry GM3YEH
0 -
[{"insert":"Previous comments were from years ago. Here Flex 6500 with V3 software and CWS V2.1. I believe I followed all instructions in SDR Bridge V3. But my Skimmer jumps in 110 Hz increments, and almost always jumps over every signal without printing. I've asked Alex (author of CWS) but with no help. Years ago CWS didn't do this. Again any ideas? 73 de bob k8ki\n"}]0
Leave a Comment
Categories
- All Categories
- 283 Community Topics
- 2.1K New Ideas
- 526 The Flea Market
- 7.5K Software
- 6K SmartSDR for Windows
- 145 SmartSDR for Maestro and M models
- 352 SmartSDR for Mac
- 249 SmartSDR for iOS
- 228 SmartSDR CAT
- 169 DAX
- 352 SmartSDR API
- 8.7K Radios and Accessories
- 7K FLEX-6000 Signature Series
- 6 FLEX-8000 Signature Series
- 840 Maestro
- 43 FlexControl
- 845 FLEX Series (Legacy) Radios
- 788 Genius Products
- 414 Power Genius XL Amplifier
- 274 Tuner Genius XL
- 100 Antenna Genius
- 242 Shack Infrastructure
- 166 Networking
- 403 Remote Operation (SmartLink)
- 127 Contesting
- 624 Peripherals & Station Integration
- 125 Amateur Radio Interests
- 860 Third-Party Software