Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.8.21 and the SmartSDR v3.8.21 Release Notes
SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
Power Genius XL Utility v3.8.9 and the Power Genius XL Release Notes v3.8.9
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.8.21 and the SmartSDR v3.8.21 Release Notes
SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
Power Genius XL Utility v3.8.9 and the Power Genius XL Release Notes v3.8.9
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Three odd behaviors using the Flex control knob
Ken - NM9P
Member ✭✭✭
More "testing" results for the software guys... 1) As I tune to either end of the display and the display begins to scroll, there are momentary hic-ups in the audio... split second drop-outs. They reoccur every 5-8 kHz or so as I continue to tune. 2) When I have two panadapters open, in this case the top on 80 and the bottom on 10 meters.... As I tune on 80 with the flex control knob the lower pan window shows and increased, spiky "noise" all across the display until I stop tuning, then goes back to normal. 3) There have been some times, especially when tuning through SWL bands using a very wide spectrum pan, that the flex control will stop responding for a couple of seconds, then rush to catch up long after I have stopped tuning. Then it begins acting very sluggishly and unpredictably. Ken - NM9P BTW - I am having a lot of fun.. getting great audio reports. nice receive, and did I say this is a heck of a lot of fun. But I am going to give this rig the run through for a couple of days in order to "earn my keep" for the early release.
0
Comments
-
Ken, All three of your reports have been turned into bug reports and have been entered into the developer's bug tracker for additional investigation. Thank you for the report.0
-
The number 2 behavior got me at FD this year but with only one slice open. Any time the flex control or the mouse wheel was used to move frequency, the noise level spiked to almost three times the normal level. Very hard to track stations near the noise floor. Is there any solution to this yet?
0
Leave a Comment
Categories
- All Categories
- 299 Community Topics
- 2.1K New Ideas
- 546 The Flea Market
- 7.6K Software
- 6.1K SmartSDR for Windows
- 149 SmartSDR for Maestro and M models
- 378 SmartSDR for Mac
- 253 SmartSDR for iOS
- 227 SmartSDR CAT
- 165 DAX
- 361 SmartSDR API
- 8.9K Radios and Accessories
- 7K FLEX-6000 Signature Series
- 67 FLEX-8000 Signature Series
- 870 Maestro
- 45 FlexControl
- 849 FLEX Series (Legacy) Radios
- 819 Genius Products
- 427 Power Genius XL Amplifier
- 286 Tuner Genius XL
- 95 Antenna Genius
- 252 Shack Infrastructure
- 173 Networking
- 411 Remote Operation (SmartLink)
- 120 Contesting
- 664 Peripherals & Station Integration
- 128 Amateur Radio Interests
- 895 Third-Party Software