Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, and Tuner Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.1.20 and the Tuner Genius XL Release Notes v1.1.20
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Frequency Display Box fixed location
Location of the frequency display boxes are apparently fixed. [To the left of the frequency selected. I note that in setting up any bandwidth on lower sideband, the display box covers up the top of the bandpass filter, obscuring the top of the scale. In addition, when selection of two frequencies close to one another, as necessary, when as NCS of a traffic net and also keeping track of off net frequency traffic , the two displays over lap and obscure each other. In the future, would there be the possibility of selecting either side of operating frequency to place the display box? Ken K7YR
3
Comments
-
Wait until the next version of SmartSDR is released. It has a new feature that will prevent the slice control panels that are in close proximity to one another from over lapping2
-
Hi Tim, Roger, Lots and Lots of features to develop. Going beck to the basics after owing the 5000A and 3000 can be frustrating, however using the past as a reference and applying a little imagination, the future is surly promising........> Ken K7YR0
-
I like the fact that in the latest version of SmartSDR that panels no longer overlap. Thanks guys. But I agree, when in LSB it would be nice if the panel was displayed on the opposite side so as not to obscure the signal's spectrum.0
-
i couldn't agree more with moving the panel to the right side when in LSB.0
Leave a Comment
Categories
- All Categories
- 244 Community Topics
- 2.1K New Ideas
- 481 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 132 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 162 DAX
- 348 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 746 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 722 Genius Products
- 388 Power Genius XL Amplifier
- 250 Tuner Genius XL
- 84 Antenna Genius
- 225 Shack Infrastructure
- 150 Networking
- 366 Remote Operation (SmartLink)
- 120 Contesting
- 580 Peripherals & Station Integration
- 114 Amateur Radio Interests
- 805 Third-Party Software