Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Transverter help
Options
Jim
Member ✭✭
Hope someone can help. Im attempting to use a Q5 Signal 144 MHz XVTR with my Flex 6400. Ive connected thee two units together according to instructions. Ive set up the XVTR on the Flex, and Ive configured a memory to access a nearby repeater. So far so good. When I key the mic, I get tones back from the repeater. I can hear QSO's on the repeater. The XVTR bargraph shows power output. My inline Power/SWR meter shows low SWR and proper power output to the antenna. No one can hear me!! I have to have a setting goofed up somewhere. Any ideas for a newbie? Im attaching a screen shot of my SDR screen. As a side issue, if I simply substitute a different rig in place of the flex it works fine. Any help greatly appreciated.
Jim KC3KRZ
Jim KC3KRZ
0
Answers
-
Jim
Your screen shot shows "PC" as the selected microphone source. Perhaps you're using a physical microphone, and you've just not selected it as the active audio source (BAL, or MIC)?
Todd, KC1SQ
0 -
In the second control panel down on the right, the mic source is set to PC and DAX is enabled. If you are using the mic plugged into the radio, the mic source should be MIC and DAX should be disabled. As it is configured, you have no connection from mic audio to the radio.
0 -
Thanks Craig and Todd. That did the trick!
0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 328 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 810 Third-Party Software