Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
SmartSDR Locks Up
Options
DonS
Member ✭✭✭
If I open two slice receivers on a single slice with one (B) at 7.020mhz and the other (A) at 7.170 mhz and set the first to cw and the second to lsb then go in and adjust the AGC-T and set (B) active and enable TX and then return to (A) none of the options work on the (A) receiver other than making it the active receiver. I have reproduced this each time I try it. If I **** the (A) slice receiver I lose both receivers. I am able to reactivate the slice rx most of the time otherwise I have to power down SmartSDR and do the same with the 6700. I am using 16.4 running on an iMAC with Parallels using Win 7 Pro.
1
Comments
-
I should add that for whatever reason cw would not work with the external keyer after the SmartSDR locked up. It was almost as if the system ignored that input, when Iambic was non-selected, however, it did work with the key plugged directly into the key jack and Iambic enabled.0
-
Don, I have added this to the developer's bug tracker for further investigation.0
-
Is this still happening after an upgrade to SmartSDR v1.0.0?0
-
After I set it up as described in the previous message and go back to the A slice everything is frozen. I can enable the A slice, however everything else is locked. I cannot enable TX on A. I did have speaker selected on A so I see the AGC-T, etc but cannot change any settings. The only thing that seems to work is that I can select the blue Ant 1 and get the drop down and change it and change it back.0
-
If I change the frequency on the A slice by double clicking to a new frequency then the A slice control becomes active again until I go back to the B slice and then return back to the A slice then the A slice freezes up again.0
-
If I **** the A slice, it also kills the B slice so when I start a new slice it comes back as the A slice then I start a second slice and I get the same problem as I previously described.0
-
V1.0.00
-
Don, I have confirmed this a a software defect and have entered it into our bug tracker for resolution. This was a good catch! Thanks for the feedback.0
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 328 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 810 Third-Party Software