Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
The latest SmartSDR Software:
SmartSDR v4.1.5 | SmartSDR v4.1.5 Release Notes
SmartSDR v3.10.15 | SmartSDR v3.10.15 Release Notes
The latest 4O3A Genius Product Software:
The latest 4O3A Genius Product Software and Firmware
SmartSDR v4.1.5 | SmartSDR v4.1.5 Release Notes
SmartSDR v3.10.15 | SmartSDR v3.10.15 Release Notes
The latest 4O3A Genius Product Software:
The latest 4O3A Genius Product Software and Firmware
How to Receive Technical Support::
If you are needing assistance with FlexRadio products, please refer to the product documentation or check the Help Center for known solutions. Need technical support from FlexRadio? It's as simple as creating a HelpDesk ticket.
If you are needing assistance with FlexRadio products, please refer to the product documentation or check the Help Center for known solutions. Need technical support from FlexRadio? It's as simple as creating a HelpDesk ticket.
Odd behavior when offset for wsjt-x is greater than 3k...anyone else see this?
mdavid01
Member
I've been spending a lot of time using WSJT-X for JT-65 and JT-9. Enjoying digital modes more than I anticipated.
I've noticed that every so often when the offset is greater than 3k the flex will show the red TX transmit, however in the waterfall it shows no signal and nothing noted in panadapter either.
Here is what SmartSDR looks like during this event

Anyone else notice this behavior with WSJT-X and SmartSDR?
I've noticed that every so often when the offset is greater than 3k the flex will show the red TX transmit, however in the waterfall it shows no signal and nothing noted in panadapter either.
Here is what SmartSDR looks like during this event

Anyone else notice this behavior with WSJT-X and SmartSDR?
1
Answers
-
Set your TX High Cut > 2900 (e.g. 4000)!
1 -
What Cedric says and don't forget to setup a JT65 profile otherwise it will be a recurring problem. I tend to forget to enable DAX as source on transmit when bouncing from JT65 and SSB modes.1
-
Dang that was fast for the exact right answer! Thanks!
0 -
Another fix for this is to use the fake split mode of WSJT-X, this will automatically increase or reduce the frequency enough to keep the transmit signal at around 1.5k and return to the correct frequency on receive.0
Leave a Comment
Categories
- All Categories
- 389 Community Topics
- 2.2K New Ideas
- 659 The Flea Market
- 8.4K Software
- 157 SmartSDR+
- 6.5K SmartSDR for Windows
- 186 SmartSDR for Maestro and M models
- 439 SmartSDR for Mac
- 275 SmartSDR for iOS
- 265 SmartSDR CAT
- 204 DAX
- 386 SmartSDR API
- 9.4K Radios and Accessories
- 53 Aurora
- 297 FLEX-8000 Signature Series
- 7.2K FLEX-6000 Signature Series
- 971 Maestro
- 58 FlexControl
- 867 FLEX Series (Legacy) Radios
- 945 Genius Products
- 472 Power Genius XL Amplifier
- 347 Tuner Genius XL
- 126 Antenna Genius
- 307 Shack Infrastructure
- 215 Networking
- 468 Remote Operation (SmartLink)
- 142 Contesting
- 813 Peripherals & Station Integration
- 144 Amateur Radio Interests
- 1.1K Third-Party Software
