Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR or 4O3A Genius Product Software?


SmartSDR v4.0.1 and the SmartSDR v4.0.1 Release Notes

SmartSDR v3.10.15 and the SmartSDR v3.10.15 Release Notes

The latest 4O3A Genius Product Software and Firmware
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

I wish to wire up a Silver Eagle D-104 Mic to use with my Maestro C

KG5PTE
KG5PTE Member ✭✭
in Maestro

Hello, with the new Maestro C having a PTT 1/8 jack that requires Tip Sleeve (TS) and the HDST 1/8 jack that requires Tip Ring Ring Sleeve (TRRS) can I wire up a 1/8 jack for a old Silver Eagle D-104 mic and make it work ? This morning at our monthly radio club meeting I asked if it could be done. The question that I was told to ask the Flex experts is this. "Will the Flex 6400 and Flex Maestro C work with a high impedance mic" ?

Thank you.

Answers

  • Mike-VA3MW
    Mike-VA3MW Administrator, FlexRadio Employee, Community Manager, Super Elmer, Moderator admin

    Typically, the Mic impedance is pretty low for these connections, but I am checking with our engineers. Usually under 100 ohms.

    For a high impedance Mic you'll like need to do some impedance matching which is pretty simple to do.

  • KG5PTE
    KG5PTE Member ✭✭

    Any word from the engineers about the D-104 Mic ?

  • Mike-VA3MW
    Mike-VA3MW Administrator, FlexRadio Employee, Community Manager, Super Elmer, Moderator admin

    The Mic Impedance on the Maestro is about 32 ohms. This is done to limit RFI issues.

  • KD0RC
    KD0RC Member, Super Elmer Moderator

    Hi James, I would just give it a try. The Flex has a built in 20 dB pre-amp if you need it. If that isn't enough, then I think that there are little amps available that fit in the D-104 base.

  • johnn1jm
    johnn1jm Member ✭✭✭

    In using a D-104 with a low impedance input, it is best to use something to match the impedance such as a transformer or an FET source follower circuit. You may be able to drive the radio without impedance matching ok but the frequency response will not be great.

    YMMV

  • KG5PTE
    KG5PTE Member ✭✭

    My Friend (NU5D) who is wiring up the D-104 mic for me told me this in response.

    Good
    info.  The cartridge itself is around 100 k ohm and needs maybe 1 Meg
    ohm in series to bring up the low end of voice (otherwise the D104 is
    very tinny)...   Trouble is 1 meg ohm in series will really really knock
    down the output of the cartridge (called a swamping resistor)...  That
    needs to be made up with a pre-amp stage.  The 20db in your radio might
    just be enough - easy to try.  I just need to wire the plug to the
    cable.  If there is not enough drive, then I might have to add a preamp -
    these are little ready made boards that boost the loudness.

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.

Comment As ...

Categories