Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
The latest SmartSDR Software:
SmartSDR v4.2.20 | SmartSDR v4.2.20 Release Notes
SmartSDR v3.10.15 | SmartSDR v3.10.15 Release Notes

The latest 4O3A Genius Product Software:
The latest 4O3A Genius Product Software and Firmware
How to Receive Technical Support::
If you are needing assistance with FlexRadio products, please refer to the product documentation or check the Help Center for known solutions. Need technical support from FlexRadio? It's as simple as creating a HelpDesk ticket.

Flex 6500 transmitting popping sound

Bob KN4HH
Bob KN4HH Member ✭✭✭
in FLEX-6000 Signature Series

This morning, I checked into my local AM net and I was told that a continuous popping noise was heard in my audio. I tried SSB and received the same report. I then disconnected the microphone and the popping can still be heard. I disconnected all peripherals leaving only DC power, LAN connection, and RF cable. The popping can still be **** the carrier. I disconnected the antenna and transmitted into a dummy load and the popping is still present. I watched the transmit waveform on the SmartSDR display. When I transmitted, I noticed that the popping was present on the baseline and did not affect the carrier itself as if the popping was a form of modulation. I tried all bands and all transmit modes with the same result.

I performed a complete factory reset and nothing changed.

Any suggestions would be appreciated.

Comments

  • Alan
    Alan Member ✭✭✭✭

    Bob

    On the Node-Red Ham Radio group, we found if we send a command to the Flex API with a Carriage Return/Line Feed included in the command, the Flex Server seemed to halt sending the VITA 49 packets, for a brief moment. This "halt" created an obvious, interruption and "popping" in the TX stream. It would be very pronounced on AM, since the carrier would be interrupted.

    Some reported the same observation with third-party applications that use TCP to command the Flex.

    As a next step to investigate the source of popping, stop all of your third party applications, check for popping. If none, you found the problem.

    Then, restart each third-party application, one at a time, check for popping until you find the culprit.

    Alan

    WA9WUD

  • David Decoons, wo2x
    David Decoons, wo2x Member, Super Elmer Moderator

    I have emailed Bob the updated VITA49 and FlexRadio flows. This should eliminate his popping due to Node Red.

    Other programs and apps that send TCP commands via API can also have the same effect if sending commands while the radio is transmitting.

    Dave wo2x

  • Alan
    Alan Member ✭✭✭✭

    oh......Bob.....I did not remember we loaded Node-Red for you.

    Looks like you and Dave have the fix in hand.

    Alan

  • Bob KN4HH
    Bob KN4HH Member ✭✭✭

    Thanks, Dave and Alan. Yes updated VITA49 and FlexRadio flows cured the problem.

    73, Bob, KN4HH

  • David Decoons, wo2x
    David Decoons, wo2x Member, Super Elmer Moderator

    Good to hear!!

    I am working on some more enhancements to the FlexRadio flow to allow auto detecting of radio model and software version then set meter numbers appropriately.

    73

    Dave wo2x

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.

Comment As ...

Categories