Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR or 4O3A Genius Product Software?

SmartSDR v3.9.19 and the SmartSDR v3.9.19 Release Notes
SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes

The latest 4O3A Genius Product Software and Firmware
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

Bands switching audio

Member ✭✭✭
edited May 2020 in FLEX-6000 Signature Series
It is probably a silly question, but could someone explain me the logic of audio level changes when switching from active Slice A to Slice B.
Slice B has audio muted, but I am puzzled why would audio on slice A drops.
Both Slices use different antennas.
https://drive.google.com/open?id=1XsPuJv3rxoSld0qPNZjaYYefbPsUa43f
Thanks
Sergey

Welcome!

It looks like you're new here. Sign in or register to get started.
Sign In
Register

Answers

  • Administrator, FlexRadio Employee admin
    edited May 2020
    The signal levels are not the same between both panadapter.  The louder panadapter (top) has a higher noise floor and will have a louder volume and a consequence of that.
  • Member, Super Elmer Moderator
    edited May 2020
    Hi Sergey, you have a different RX EQ profile for each receiver.  Make them the same, and you will not see this effect.
    73,
    Len, KD0RC
  • Administrator, FlexRadio Employee admin
    edited May 2020
    Better yet, use the AGC-T as this is that it is for.  The AGC-T is too high on the top panadapter so it is amplifying band noise.
  • Member ✭✭✭
    edited May 2020
    Tim, I understand the noise level is different between 2 bands.
    But I am not listening 6m on that video, as you see on the video Speaker is Muted on 6m.
    So, expect to hear audio on Slice A without level changed. Am I wrong?

    The reason I switch between them is to have control of the buttons and sliders for Bandwidth and was puzzled by audio effect.
    Thank you
    Sergey, KN7K
  • Member, Super Elmer Moderator
    edited May 2020
    Sergey, I notice in the video that your RX EQ settiings change when you select the 6M RX.  Could that be the issue?  Set the 6M RX EQ the same as the 160M RX EQ and see if that makes a difference.
    Len
  • Member ✭✭✭
    edited May 2020
    Thank you Len for reply.
    I am trying to understand why it is relevant if audio from Slice B is muted.
    This is my confusion point.
    Sergey, KN7K
  • Member, Super Elmer Moderator
    edited May 2020
    Yep, I understand.  What I am suggesting is to set the RX EQ the same, and see if the issue clears.  If it does, it may indicate a bug in SmartSDR where it is using the wrong RX EQ.  If it does not clear it up, there may be something else like AGC-T or the ant preamp at play.  Which radio do you have?  I have a 6400, so I cannot adequately experiment with this because I have only one Spectral Capture Unit.

    Len
  • Member ✭✭✭
    edited May 2020
    i have 6600

Leave a Comment

Welcome!

It looks like you're new here. Sign in or register to get started.
Sign In
Register

Quick Links

Categories