Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
6300 no RX audio in AM & SAM modes
Options
Bob Arney
Member
No receive audio in AM & SAM modes, audio can be heard in USB or LSB modes. TX audio and operation in AM is normal. No audio is produced by the radio in these two modes. Radio is running software version 2.6.1.146. Problem started about two weeks ago, no changes to software or configuration were made. I did reload the software but problem still exists.
0
Comments
-
AM audio re directed to a rear panel connection?0
-
AM audio directed to a rear panel connection?0
-
is your Squelch enabled0
-
Yes, all audio is sent to the rear speaker output. I have always had the audio connected in this way and it worked without issue.
Just discovered something interesting. If the audio slider in the software control is in the center position, equal right and left, I have no audio out on AM and SAM modes. But, all other modes operate normally with audio out in the center position and fades right and left properly. I never use the R/L slider so I did not notice it prior, always kept it centered between R&L.0 -
No squelch.
0 -
there's a squelch on the 6000 series Flex?
0 -
Woops Just in the FM mode not on AM
0 -
Bob,
My suggestion would be … export your profiles, and do a factory reset on the radio, test the AM problem, then reimport the profiles and test again.
My other suggestion, has anything changed in your external audio system that would invert the audio phase of one of your speakers ?
AL, K0VM
1 -
I did the factory reset and reinstalled the software but it did not correct the issue. I did not export the profiles and reinstall them. I will give it a try.
I would also suspect the audio connections or speaker system but this only occurs on AM and SAM. Audio output works fine on all other modes. Other modes have audio output when the slider is centered.
Thanks,0
Leave a Comment
Categories
- All Categories
- 248 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.4K Software
- 5.9K SmartSDR for Windows
- 135 SmartSDR for Maestro and M models
- 330 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 344 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 773 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 727 Genius Products
- 391 Power Genius XL Amplifier
- 252 Tuner Genius XL
- 84 Antenna Genius
- 224 Shack Infrastructure
- 151 Networking
- 372 Remote Operation (SmartLink)
- 118 Contesting
- 583 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 810 Third-Party Software