Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
If you are having a problem, please check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

Win 10 Upgrade 1909

W9WLX_ChuckW9WLX_Chuck Member ✭✭
Using v3.1.8 and upgraded to Win 10 1909 without any DAX naming issues.  The upgrade seemed pretty light, so not sure if there was anything in the upgrade that would have caused the problem.   In any event, thanks Flex team for resolving this one!

Chuck, W9WLX

Comments

  • Santiago Mejia - HI8SMXSantiago Mejia - HI8SMX Member ✭✭
    edited March 2
    One can conclude that if Win 10 is used version 3 is better recommended?

    Santiago
  • John WA7UARJohn WA7UAR Member ✭✭
    edited November 2019
    Yes. For me, since upgrading to version 3.1.7, I have not had any Win 10 DAX renaming issues. 
  • Santiago Mejia - HI8SMXSantiago Mejia - HI8SMX Member ✭✭
    edited November 2019
    That is something I must consider then, because I’m upgrading to a new shack PC with Windows 10.
  • edited November 2019
    I did the 1909 feature upgrade on both computers this morning and all went well.  I've seen no DAX problems since 3.1.x was released.

  • Santiago Mejia - HI8SMXSantiago Mejia - HI8SMX Member ✭✭
    edited March 2
    Finally made the move to version 3.1.x to go with my new shack PC. Fingers crossed for Windows 10 updates from now on.
  • Ernest - W4EGErnest - W4EG Member ✭✭
    edited November 2019
    Installed Win10 v1909 and running SmartSDR v2.6.1 and DAX & CAT and other related software; (FT-8) are operating normal. 
    NO ISSUES ENCOUNTERED ON THIS WIN 10 SOFTWARE INSTALLATION!
  • WA2SQQWA2SQQ Member ✭✭
    edited November 2019
    I'm using the latest 2.x version. On Saturday I sat through the "October" Win update. While holding my breath, I restarted and all seemed OK. I did experience two minor issues.  DAX no longer starts automatically. Once I manually activate it, all works just fine. On my dual monitor setup, the two monitors got reversed, and all the program icons moved to the primary monitor. Simple fix moving them. I don't regard either as being caused by Flex software.
  • W9WLX_ChuckW9WLX_Chuck Member ✭✭
    edited November 2019
    You can set DAX and CAT to auto launch with SSDR.  On the DAX and CAT control panels, check the On Startup, Auto Connect Last Radio. uto 
  • WA2SQQWA2SQQ Member ✭✭
    edited November 2019
    Yes, already done. 
  • Logan KE7AZLogan KE7AZ Member ✭✭
    edited December 2019
    I "downgraded" from Win 7 to Win 10.  Lots of problems from a formerly stable, reliable system.  The 1909 upgrade had downloaded but not installed.  When I opened SmartSDR, I got a portcls.sys BSOD.  A couple of reboots and 1909 installed.  When I opened SmartSDR, all of my CAT entries were gone and I had the default set!  The virtual ports are still listed in the Device Manager.  So the adventure begins as I try to restore my setup....  A knob radio looks better every day that my $1500 deposit sits in Watsonville waiting for the new year.f
  • W9WLX_ChuckW9WLX_Chuck Member ✭✭
    edited December 2019
  • WA2SQQWA2SQQ Member ✭✭
    edited December 2019
    I might be wrong, but wasn't the latest updates supposed to fix problems associated with Windows updates? I am not going to brag, but so far I have not had any of these issues. The only thing that I might be able to attribute this to is that I always shut down all Flex and Flex associated software before allowing any updates. The repair process is not that difficult and enjoying my Flexradio is well worth the occasional PIA.
  • W9WLX_ChuckW9WLX_Chuck Member ✭✭
    edited December 2019
    I also take it one step further and have a short .bat file that I run which does a 'taskkill' on each task Smart SDR may be running--just to make sure there are no remnants left running.
  • Bob Gerzoff, WK2YBob Gerzoff, WK2Y Member ✭✭
    edited December 2019
    I went from 1809 to 1909 with no issues, Windows wise,  DAX or otherwise.  It did take a while and I had to restrain myself and just let it do it's thing.  
  • Logan KE7AZLogan KE7AZ Member ✭✭
    edited December 2019
    I tried that but it didn't work.  I put in a Help Desk ticket and Tim pointed me to a file that I needed to delete.  That fixed the problem.
  • Logan KE7AZLogan KE7AZ Member ✭✭
    edited December 2019
    I usually uninstall SmartSDR before an update.  Unfortunately, unknown to me, the 1909 update was lurking in the background waiting for a reboot.  When I started SmartSDR to check a frequency, I got the PORTCLS.SYS BSDOD and it shut down SmartSDR, forced a reboot and "we are off to the races."  Got it straightened out with a Help Desk ticket, this morning.
  • W9WLX_ChuckW9WLX_Chuck Member ✭✭
    edited December 2019
    Yep, deleting CAT.setting is part of the procedure.  Pleased to hear you're back up!
  • Santiago Mejia - HI8SMXSantiago Mejia - HI8SMX Member ✭✭
    edited May 23
    Just did the 1909 myself a few minutes ago. While it wasn´t a confortable wait at the end I had no issues. So far, that is.
  • k3Timk3Tim Member ✭✭
    edited December 2019
    Same story here, two PC's updated with latest 1909 and no issues.

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.