Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.9.18 and the SmartSDR v3.9.18 Release Notes
SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
Power Genius XL Utility v3.8.9 and the Power Genius XL Release Notes v3.8.9
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.9.18 and the SmartSDR v3.9.18 Release Notes
SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
Power Genius XL Utility v3.8.9 and the Power Genius XL Release Notes v3.8.9
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Flex 6400M does not boot anymore after software upgrade.
Veiko Värk
Member
Hei .
Yesterday I installed the new SmartSDR 3.0.27 to my FLEX6400M.Everything was fine until one moment the program installation stopped, I waited for an hour to complete the installation, but it didn't happen.Then I turned off the FLEX6400M.Then I turned off the FLEX6400M. When I restarted it, the missing network connection and FLEX did not boot up.I tried many times but failed.Still the red light flashed.I also replaced the network cable, but it didn't help. There is a network connection for all of these other devices.Is it possible that the boot disk failed or the network card is faulty inside the Flexradio? Please ask for help. I also did the factory reset but there was no help.
Yesterday I installed the new SmartSDR 3.0.27 to my FLEX6400M.Everything was fine until one moment the program installation stopped, I waited for an hour to complete the installation, but it didn't happen.Then I turned off the FLEX6400M.Then I turned off the FLEX6400M. When I restarted it, the missing network connection and FLEX did not boot up.I tried many times but failed.Still the red light flashed.I also replaced the network cable, but it didn't help. There is a network connection for all of these other devices.Is it possible that the boot disk failed or the network card is faulty inside the Flexradio? Please ask for help. I also did the factory reset but there was no help.

0
Comments
-
Maybe Flex send to me a new image for SD card?0
Leave a Comment
Categories
- All Categories
- 322 Community Topics
- 2.1K New Ideas
- 588 The Flea Market
- 7.8K Software
- 6.2K SmartSDR for Windows
- 165 SmartSDR for Maestro and M models
- 391 SmartSDR for Mac
- 257 SmartSDR for iOS
- 246 SmartSDR CAT
- 177 DAX
- 368 SmartSDR API
- 9K Radios and Accessories
- 12 Aurora
- 147 FLEX-8000 Signature Series
- 7.1K FLEX-6000 Signature Series
- 904 Maestro
- 50 FlexControl
- 854 FLEX Series (Legacy) Radios
- 861 Genius Products
- 443 Power Genius XL Amplifier
- 304 Tuner Genius XL
- 114 Antenna Genius
- 272 Shack Infrastructure
- 192 Networking
- 436 Remote Operation (SmartLink)
- 135 Contesting
- 711 Peripherals & Station Integration
- 131 Amateur Radio Interests
- 935 Third-Party Software