Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Flex 6400M does not boot anymore after software upgrade.
Options
Veiko Värk
Member
Hei .
Yesterday I installed the new SmartSDR 3.0.27 to my FLEX6400M.Everything was fine until one moment the program installation stopped, I waited for an hour to complete the installation, but it didn't happen.Then I turned off the FLEX6400M.Then I turned off the FLEX6400M. When I restarted it, the missing network connection and FLEX did not boot up.I tried many times but failed.Still the red light flashed.I also replaced the network cable, but it didn't help. There is a network connection for all of these other devices.Is it possible that the boot disk failed or the network card is faulty inside the Flexradio? Please ask for help. I also did the factory reset but there was no help.
Yesterday I installed the new SmartSDR 3.0.27 to my FLEX6400M.Everything was fine until one moment the program installation stopped, I waited for an hour to complete the installation, but it didn't happen.Then I turned off the FLEX6400M.Then I turned off the FLEX6400M. When I restarted it, the missing network connection and FLEX did not boot up.I tried many times but failed.Still the red light flashed.I also replaced the network cable, but it didn't help. There is a network connection for all of these other devices.Is it possible that the boot disk failed or the network card is faulty inside the Flexradio? Please ask for help. I also did the factory reset but there was no help.
0
Comments
-
Maybe Flex send to me a new image for SD card?0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 328 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 810 Third-Party Software