Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
I want to operate my 6300 on 7295 but the xmit is "not ready" when on AM
Options
Bob Doolittle
Member
The band edge stops even narrow AM signals from being xmited
0
Answers
-
What is you XMIT bandwidth? If TX Freq + 1/2 the bandwidth adds up to more than 7300 then you would be out of band. Just a guess.
73, Andreas, N6NU0 -
Bob,
I just tested it here using my 6600 running version 2.49 and it works. I cannot recreate your error. My transmit bandwidth is set at low 100 and high 2900.
73,
Mack
W4AX
Alpha Team0 -
It sounds like a transmit bandwith problem to me as well. I think for am the default is 6Khz. And can go much higher. Hopefully, adjusting the bandwidth manually will take care of it. Most AM activity on 40 meters is much lower in freq. James WD5GWY0
-
Bob - what self-respecting AM'er would limit their bandwidth to only 10 kHz? <grin>
As you can see, setting your Flex to 5000 hz high-cut would place your spectrum up against the 7.3 MHz band limit. Anything above that could be a potential band violation. Just remember that your actual AM bandwidth is potentially (dependent on modulation frequency) twice the high-cut setting.
Not sure 10 kHz bandwidth qualifies as narrow AM ... however, I admit to feeling really pinched below 8 kHz <donning flame suit>.
73's ...
0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 489 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 223 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 766 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 813 Third-Party Software