Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
If you are having a problem, please check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

Furnace Blower RFI - Suggestions?

Sorry but the pictures that follow are gruesome and may churn the stomach of even the most stout OM or XYL...

I have a 1.5 yr old Goodman furnace that has an ECM blower motor.  In diagnosing the situation, when at the furnace and watching my waterfall, 10m gets blown out as visualized below (2nd one) the moment the relay flips and blower starts moving.  These aren't birdies they are a flock!





I am in the process of working with installer and mfg but it's not looking promising.

I have found these two articles and am headed down a path of suppressing RFI on the wires to the motor- hoping its there....  Curious if any of you have seen such a signature and have any tips as I hate to stumble around for months to sort this out - although the 10m prop is shot for a year or two more so I guess I have time....

Resolving Furnace and A/C RFI (Radio Frequency Interference) - ARRLwww.arrl.org/files/file/.../Solving%20Furnace%20and%20AC_RFI_KM4LHZ_v9.pdf

https://www.eham.net/articles/32146

Thanks,

-Dave

Answers

  • KC2QMA_JohnKC2QMA_John Member ✭✭
    edited January 2019

    It's amazing how this stuff passes FCC certification? And yet when an amateur radio company wants to make a new radio or amp they put the screws to them.


    Well good luck, looks like that RFI motor filter will help a lot.
  • edited January 2019
    Hmm, never thought about that.  I have some unsolved RFI, will keep my furnace blower in mind.

  • ChuckChuck Member
    edited September 2019
    Dave, I can't see the frequency range of the EMI on 10M, but it appears quite large.  Can you please clarify the range?  In my experience with Trane ECM units, the EMI signature is a series of perhaps 50 closely spaced pulses spread across approximately 1 KHz.  These groups of pulses are approximately 18 KHz apart and repeat over several MHz of the HF spectrum.

    The attached presentation by KM4LHZ is EXCELLENT and mirrors my experience in virtually every way.  Be careful to explore ALL the wires that exit the metal enclosures as they can easily be antennas conducting the EMI to the outside world..  If you happen to have motors manufactured by Regal Beloit, you are fortunate.  The engineering staff was very supportive five+ years ago when I encountered problems with their motors. 

    I suggest you follow the analysis and resolution recommendations in the paper and report your progress, good or bad, so readers here may offer their experience.
    ---
    Chuck, AE4CW
  • Dave - N6XVZDave - N6XVZ Member
    edited January 2019
    Chuck Appx 24.8 to 31.8 MHz. So 7mhz. Huge. Peaks every 15 kHz. It seems like such a large range vs what others including you mention seeing. I do have to ferret out the motor mfg. one can hope it is the same mfg. Really the only wires exiting the enclosure are Thermostats and power. But will keep them in suspicion. image
  • N8SDRN8SDR Member
    edited February 2019
    Dave, Have you looked at whole house AC filters  something like the Morgan 330 units, http://www.surgestop.com/surge-products/m-330.html  . I think someone else now builds there products - I have a few of the 400 series and they seem to work at taking out or reducing  issues I have had. and will probably add the 330 as well.
  • Larry _ W8LLLLarry _ W8LLL Member ✭✭
    edited February 2019
    My washer/dryer combo did this until i put some mix 31 snap ons on the 240vac power cable right up to the back panel. This prevents the motor that is emmitting rfi to use the power cable as an antenna and transmit it farther and stronger.
  • Mark Aaker K6UFOMark Aaker K6UFO Member ✭✭
    edited February 2019
    When my new furnace had this problem several years ago, the following steps helped.
    The manufacturer had a "RFI kit" available to installers, and it was basically just an 
    AC line filter. It helped. I then used a small loop as an antenna "sniffer" as I tried to 
    see where the noise was coming from, even taking the front panel off. The motor wires 
    were the worst, so I replaced them with a "twisted pair" with a small ferrite at each 
    end and the noise was reduced to negligible levels at my antennas.
  • Ed JohnsonEd Johnson Member ✭✭
    edited April 2019
    I had the same problem.. Popped open the inside unit and installed 10 split ferrites Mix 31 on all wiring harnesses that I could get to..... including wires to thermostat (great antenna).  Problem is history.
  • Andy - KU7TAndy - KU7T Member
    edited January 2019
    Same issue here, although the spectrum looks different. I am still trying to get my Trane service company to actually understand what I am talking about. :-(
    Anway, here is how my Heatpumps look like on 20 and 15



    73
    Andy
    KU7T
  • ChuckChuck Member
    edited February 2019
    Dave,
    I have seen the EMI extend 7 MHz and more.  The peaks from the EMI emitting motors consists of clusters of many very narrow pulses (~50) spanning approximately 1 KHz.  And, these pulse group repeated approximately every 18 KHz over many MHz.  The noise signature I see in your photo above is different from anything I have seen coming from my HVAC motors.
    Chuck
  • Dave - N6XVZDave - N6XVZ Member
    edited September 2019
    Moral of the story..... Don't buy a Goodman furnace.

    My installer wanted to help but it was beyond their expertise.  They reached out to Goodman and they said "dunno".  Called Goodman customer support and they said call installer.  So dead ends everywhere.  Sadly I didn't have the motor referenced in the above articles....

    So I went to Mouser and loaded up on all sorts of ferrite's.

    Clip on's only marginally made a difference.  The real winner-=> Ferrite Rings:

    I was luck enough to have enough wire play to take each wire and wrap it 7times thru a ferrite ring.  Problem solved and all noise gone.  Wasn't the power nor the thermostat wires resonating; it was the PCM motor.  As we know impedance of a choke is proportional to the square of the number of turns.  7 turns was my magic and thankfully enough wire for it. 

    Here's a pic of the fix:



    I used some zip ties to carry the weight of the ferrite rings so as not to unduly stress the wires up at the motor.

    So when in doubt, ask a Ham.  We can fix it!

    10m is blessedly quiet now when the motor is running.  Now if only some Sporadic E would show up!

    73's.
  • PatrickPatrick WH6HI Member ✭✭✭
    edited June 2
    After reading the various comments and sujestions, most are what I would have done, there is one more thing you should do. Report this to your FCC field office and give them all the details of what you have done. With the current political regime in office. All prevention regulations at the various regulatory agencies have changed to self regulation policy. So the only way to get action on an issue is to report problems or proceed with legal action.
  • Dave - N6XVZDave - N6XVZ Member
    edited February 2019
    Pat- One of the hot topics in our community besides merits or lack of them for FT8, or people constantly changing call signs and locking them out or.... Is whether this device falls under FCC regulations or not. I find arguments on both sides and struggle to overcome my apathy to convince FCC and MFG of their error For example see slide 30 of the ARRL preso I listed at the start. It claims no standard for incidental emissions below 30mhz. I haven’t found any good examples of how one of us has pursued this path and made a difference. Tnx
  • k3Timk3Tim Member ✭✭
    edited February 2019
    The regulations are in chapter 47 /  part 15 / paragraph 103 of the Federal Regulations. This is a link to the FCC clarifying the rules relative home appliances:

    https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=33062

    A washing machine / dryer is exempt but a hair straightener is not. I wonder who came up with the list...
    Be that as it may the last paragraph seems to keep the MFG on the hook for RFI problems: 

    "An exempt appliance is only exempt from equipment authorization procedures for the functions associated with the digital device circuitry. The appliance remains subject to the requirements in Section 15.5 requiring the device not cause harmful interference"

    _..--
    TiM

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.