Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.8.23 and the SmartSDR v3.8.23 Release Notes
SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
Power Genius XL Utility v3.8.9 and the Power Genius XL Release Notes v3.8.9
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.8.23 and the SmartSDR v3.8.23 Release Notes
SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
Power Genius XL Utility v3.8.9 and the Power Genius XL Release Notes v3.8.9
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Flex-5000, PowerSDR, and WSJT-X
K1SZO
Member ✭✭
Hello all,
I have a friend that has a Flex-5000, uses PowerSDR, and wants to setup WSJT-X with it. I've read the howto knowledge base article on setting these up, but the instructions seem quite dated and do not seem to jive anymore.
We were using com-0-com and VAC, but PowerSDR did not like it when I set the driver to Windows WDM-KS and the Virtual Cable 1 and 2.
Also, I can't for the life of me figure out how to get CAT control working either.
Does someone know of some updated instructions to get this configuration up and running?
73, David ~ K1SZO
I have a friend that has a Flex-5000, uses PowerSDR, and wants to setup WSJT-X with it. I've read the howto knowledge base article on setting these up, but the instructions seem quite dated and do not seem to jive anymore.
We were using com-0-com and VAC, but PowerSDR did not like it when I set the driver to Windows WDM-KS and the Virtual Cable 1 and 2.
Also, I can't for the life of me figure out how to get CAT control working either.
Does someone know of some updated instructions to get this configuration up and running?
73, David ~ K1SZO
0
Answers
-
RE setting up the CAT - you might make note of this one particular setting that drove me nuts till I finally figured it out. See this link to my previous post https://community.flexradio.com/flexradio/topics/wsjt-x-with-powersdr-and-dxlab
0 -
I have the same hardware setup, also using com-0-com and VAC. As driver for VAC I use MME. Though for CAT I use DXLab Commander.
No problems at all.
73, Peter - HB9BUN0 -
I use com0com, vac line 1 for in/out and omnirig Working fine for me
73 oz1hdf0
Leave a Comment
Categories
- All Categories
- 339 Community Topics
- 2.1K New Ideas
- 580 The Flea Market
- 7.8K Software
- 6.2K SmartSDR for Windows
- 161 SmartSDR for Maestro and M models
- 387 SmartSDR for Mac
- 253 SmartSDR for iOS
- 244 SmartSDR CAT
- 177 DAX
- 367 SmartSDR API
- 9K Radios and Accessories
- 7.1K FLEX-6000 Signature Series
- 127 FLEX-8000 Signature Series
- 893 Maestro
- 50 FlexControl
- 853 FLEX Series (Legacy) Radios
- 849 Genius Products
- 438 Power Genius XL Amplifier
- 298 Tuner Genius XL
- 113 Antenna Genius
- 269 Shack Infrastructure
- 190 Networking
- 429 Remote Operation (SmartLink)
- 134 Contesting
- 702 Peripherals & Station Integration
- 131 Amateur Radio Interests
- 924 Third-Party Software