Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
If you are having a problem, please check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need the latest SmartSDR and Power Genius Software?

SmartSDR v3.1.12 and the SmartSDR v3.1.12 Release Notes. | SmartSDR v2.6.2 and the SmartSDR v2.6.2 Release Notes.
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes. | Power Genius XL Firmware v3.4.16. | Power Genius XL Utility v2.2.10.

5 meters on M radios

Rich McCabeRich McCabe Member ✭✭
edited June 2020 in FLEX-6000 Signature Series
I assume this is a bug.

The manual says "The value displayed in each meter can be selected from a set of five meters by tapping on the meter."

On my 6600M I can hit the plus and get six meters. Nothing new to select so one would always be a duplicate I think.

Rich
kd0zv

Completed · Last Updated

Answers

  • Tim - W4TMETim - W4TME Administrator, FlexRadio Employee admin
    edited June 2020
    It's a doc issue.  This was a holdover from the Maestro doc.  Thanks for pointing it out.
  • Rich McCabeRich McCabe Member ✭✭
    edited June 2020
    Tim, not a software issue too?  Why have six meters on the 6600m when there are only 5 types?  At least I think so.  Unless one is for use on second panafall and I did not catch it.

    Rich
  • Tim - W4TMETim - W4TME Administrator, FlexRadio Employee admin
    edited February 2018
    I'm looking into it.
  • Rich McCabeRich McCabe Member ✭✭
    edited February 2018
    FYI


    image
  • Tim - W4TMETim - W4TME Administrator, FlexRadio Employee admin
    edited February 2018
    That helps.  Looks like a bug.  I added it to the bug tracker as issue #6008
  • Reggie-k6xrReggie-k6xr Member ✭✭
    edited February 2018
    on the 6400M I can display more than 5 meters as well,  but they are duplicates! 
  • Eric-KE5DTOEric-KE5DTO Administrator, FlexRadio Employee admin
    edited February 2018
    There are more meters depending on what hardware is present (aka Power Genius).  This also leaves room for expansion when/if we decide to add more meters.  :)
  • K1UO - LarryK1UO - Larry Member ✭✭
    edited February 2018
    One can never have enough meters ;-)
  • David Decoons, wo2xDavid Decoons, wo2x Member ✭✭✭
    edited February 2018
    Don’t forget several meters for PG XL integration so you need the room for the extra meters. Dave wo2x
  • James WhitewayJames Whiteway Member
    edited February 2018
    Is that coder speak for, oop's we overlooked that! ? It's not a bug, it's a Feature!
  • Rich McCabeRich McCabe Member ✭✭
    edited February 2018
    Well there is a mistake somewhere because  it does not match the manual :)

    I can see having the extra space available but no reason to turn on extra duplicate meters unless the option (PGXL as an example) is installed.
  • James WhitewayJames Whiteway Member
    edited February 2018
    Someone didn't pay close attention and keep a count of Objects/Controls, as they are created or destroyed as needed. Simple coding error that even a truck driver could make! :-)
  • Rich McCabeRich McCabe Member ✭✭
    edited February 2018
    Now that you have your radio, you are getting pretty sassy James :)

  • James WhitewayJames Whiteway Member
    edited February 2018
    Meeeeeeeeeeee??????? Yeah, you're probably right. But, I was writing code for my 6300 and then the 6500 when I had them. And errors like the above were common,,,,,,,unfortunately! But, since I was not only the coder, I was the Beta tester too. Plus, I was my only user! So, I could get away with stuff like that. But, I had to toss out a little tease at Steve and Eric too. (keeps them honest!)
     
  • NX6D DaveNX6D Dave Member ✭✭
    edited June 2020
    At the time the documents were written, there were 5 distinct meters that could be assigned to any of the six slots.  The number of slots is set by the screen real estate; the number of meters that you can select from is determined by the configuration of the radio system.

    For instance, when the PowerGenius XL amp is connected, three additional meters are available (I think it is three), so the six slots could be taken up quickly enough.
  • David Decoons, wo2xDavid Decoons, wo2x Member ✭✭✭
    edited February 2018
    Yes, threeadditional meters with PG XL Dave wo2x
  • Rich McCabeRich McCabe Member ✭✭
    edited February 2018
    Yea I get all that. But with "software" radios there is no reason to have one extra meter slot available for hardware not installed.   Since the PGXL has three, adding one appears to just be a mistake. No big deal.

    Just trying to figure out a discrepancy from the manual.
  • Eric-KE5DTOEric-KE5DTO Administrator, FlexRadio Employee admin
    edited February 2018
    As discussed in this morning's defect review, the engineers are much more likely to create more meters to fill that open slot than to remove an "extra" one.  ;)
  • Rich McCabeRich McCabe Member ✭✭
    edited February 2018
    Thanks Eric.

    Just to be clear, the -4V to  0V ALC is for the amplifier?  So there are 4 usable meters for the actual radio ?  I did not see this in the manual. Just this.

    When the meters are displayed, the panadapter(s) are made narrower and move to the left side of the display; the meters are displayed on the right. “Plus” and “minus” buttons are displayed below the meters. Tapping the “plus” button adds a meter, tapping a “minus” button removes a meter. The value displayed in each meter can be selected from a set of five meters by tapping on the meter.

    So just ignore two of the slots when dealing with radio only?


    73
    Rich




  • Eric-KE5DTOEric-KE5DTO Administrator, FlexRadio Employee admin
    edited February 2018
    The ALC is actually a radio meter for the ALC interface on the radio for use with older amplifiers that require an ALC circuit.  We do not use this with the Power Genius, nor is this interface recommended unless absolutely necessary.
  • Rick WN2CRick WN2C Member ✭
    edited February 2018
    Since there are 6 meters, can one be programmed to be a volt meter so one does not have to run a third party program?  I know it is going to take a software tweak to do this,
  • David Decoons, wo2xDavid Decoons, wo2x Member ✭✭✭
    edited February 2018
    That is a good idea Rick. Dave wo2x
  • Eric-KE5DTOEric-KE5DTO Administrator, FlexRadio Employee admin
    edited February 2018
    This is a reasonable ask and is certainly technically possible.  I will put this in our system (#6046).
  • Rich McCabeRich McCabe Member ✭✭
    edited February 2018
    Temp would be nice as well :)

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.

Home • FLEX-6000 Signature SeriesComment As ...

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

Sign In Register
New Discussion Ask a Question

Categories