Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Strange Smartlink and router behavior
Options
Dave - WB5NHL
Member ✭✭
I want to report some strange behavior that might help others.
My network is connected to the internet via an Atlantic Broadband cable modem. The cable modem is a Cisco DPC3827 modem/router. This cable modem enables Upnp by default and I logged into the modem and verified that was enable.
Myself and another Flex owner tested access to my Flex via Smartlink. Below is a summary of results.
1. Remote LAN to my Flex via broadband cable modems - success (2 different locations)
2. Remote connection via Verizon cellphone hotspot - failure
3. Remote connection via Karma Go hotspot - failure
At this point I was blaming port blocking on the hotspots. As a last thought I tried port forwarding of the Smartlink TCP and UDP ports on my cable modem (Upnp is still enable).
Success on ALL connections!!!! I do not understand this behavior but everything is working!
My network is connected to the internet via an Atlantic Broadband cable modem. The cable modem is a Cisco DPC3827 modem/router. This cable modem enables Upnp by default and I logged into the modem and verified that was enable.
Myself and another Flex owner tested access to my Flex via Smartlink. Below is a summary of results.
1. Remote LAN to my Flex via broadband cable modems - success (2 different locations)
2. Remote connection via Verizon cellphone hotspot - failure
3. Remote connection via Karma Go hotspot - failure
At this point I was blaming port blocking on the hotspots. As a last thought I tried port forwarding of the Smartlink TCP and UDP ports on my cable modem (Upnp is still enable).
Success on ALL connections!!!! I do not understand this behavior but everything is working!
0
Comments
-
Out of curiosity, using your hotspot and Verizon (LTE?) before port forwarding, was the radio discoverable even though you could not establish a connection?
Jim, K6QE
0 -
Yes, once the email id and password were entered the radio was available. However, the Smartlink test failed and the remote could not connect.
0
Leave a Comment
Categories
- All Categories
- 245 Community Topics
- 2.1K New Ideas
- 490 The Flea Market
- 7.4K Software
- 5.9K SmartSDR for Windows
- 135 SmartSDR for Maestro and M models
- 327 SmartSDR for Mac
- 243 SmartSDR for iOS
- 224 SmartSDR CAT
- 163 DAX
- 347 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 727 Genius Products
- 392 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 811 Third-Party Software