Skip to content
  • Register
    • Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
    Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?

    SmartSDR v3.8.23 and the SmartSDR v3.8.23 Release Notes
    SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
    Power Genius XL Utility v3.8.9 and the Power Genius XL Release Notes v3.8.9
    Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
    Antenna Genius Utility v4.1.8
    If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
    Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

    Will software version 2.0 be available at Dayton 2017 ?

    Member
    edited February 2020 in FLEX-6000 Signature Series
    I would like to know if software version 2.0 will be out in time for dayton this year ?  

    Welcome!

    It looks like you're new here. Sign in or register to get started.
    Sign In
    Register

    Answers

    • Member ✭✭✭
      edited May 2017

      NDA.... BUT some parts of V2.0 were visible to the Public at Visalia

      So at least those parts would seem very likely

      You will need to wait on pins and needles to see what Flex actually reveals at Dayton.

    • Member ✭✭
      edited May 2017
      If Flex told you, they would have to **** you.
    • Member ✭✭✭
      edited May 2017
      What is this "Dayton" of which you speak?

      Do you mean the Xenia Hamvention?
    • Member ✭✭✭
      edited May 2017
      You must men the Xenia Cow Sheds!
    • Member ✭✭✭
      edited February 2019
      Many manufacturers showcase new products at Hamvention. Flex has several times. If 2.0 is ready to show off, I'm sure they will attract a lot of booth traffic for it. If it's not, well, they can show off some mighty fine hardware and still get lots of traffic. Always eager to see what the Austin Skunkworks has come up with for us!

    • Member ✭✭✭
      edited May 2017
      Just be sure to watch your step while on the premises. I'm told that race horses will be on the property.

    • Member ✭✭
      edited May 2017
      I fully understand. The homeowner looked at me yesterday and asked when was the roof going to be put on. I told her when the roof trusses get delivered!

    • Member
      edited February 2020
      Hi Tim. I am more than happy to have my flex available for the demonstration. The radio is connect to a 307 ft extended double zepp. 73, Mike
    • Member ✭✭
      edited May 2017
      Hi Tim, are you able to confirm if it have the ability for multiple clients to simultaneously connect to the radio at the same time?
    • Administrator, FlexRadio Employee admin
      edited May 2017
      Thanks for the offer, but have it covered.
    • Administrator, FlexRadio Employee admin
      edited May 2017
      I can confirm that is a feature planned for the 2.x release cycle.  We will not be showing the multi-client feature at Hamvention.
    • Member ✭✭
      edited May 2017
      Ok, thanks for the response!  Looking forward to v2!
    • Member ✭✭✭
      edited May 2017
      @JD  

      Apparently the foundation has been poured at least.

      @Tim

      If you have downloaded the Green Heron remote control app, I can let you into my remote 6700 and control the Radio on/off and RX antenna direction switching on both RX ports.  The 4O3A 8X2 switch will put the right TX antenna on the radio in case there is Xmitting involved regardless of xmit antenna port selected.

      Since there is no trip to Xenia for me, I hope someone videos some of the capabilities of V2.0 to share.

      Regards
      Larry  k1UO
    • Administrator, FlexRadio Employee admin
      edited May 2017
      We have plenty of stations lined up.  Thanks for the offer.
      I am sure someone will be live streaming it.  Maybe I'll do it on Facebook
    • Member ✭✭
      edited May 2017
      YES!! please livestream a demo of all the new stuff on facebook. :) 
    • Member ✭✭
      edited May 2017
      Tim, your post today has a bad link in it to the Smart Link flyer. Just wanted to let you know it is 404'ing.  Didn't know how else to reach you on here.
    • Member ✭✭✭
      edited May 2017
      I'm guessing the link was taken down deliberately because it contained references to (still unannounced) products -- likely to be announced at Xenia.

    Leave a Comment

    Welcome!

    It looks like you're new here. Sign in or register to get started.
    Sign In
    Register

    Quick Links

    Categories