Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Will software version 2.0 be available at Dayton 2017 ?
John Molenda
Member
I would like to know if software version 2.0 will be out in time for dayton this year ?
0
Answers
-
NDA.... BUT some parts of V2.0 were visible to the Public at Visalia
So at least those parts would seem very likely
You will need to wait on pins and needles to see what Flex actually reveals at Dayton.
0 -
If Flex told you, they would have to **** you.1
-
What is this "Dayton" of which you speak?
Do you mean the Xenia Hamvention?0 -
You must men the Xenia Cow Sheds!1
-
Many manufacturers showcase new products at Hamvention. Flex has several times. If 2.0 is ready to show off, I'm sure they will attract a lot of booth traffic for it. If it's not, well, they can show off some mighty fine hardware and still get lots of traffic. Always eager to see what the Austin Skunkworks has come up with for us!
0 -
We are planning on demonstrating the SmartLink feature and a few other goodies that will be in SmartSDR v2.0 at Dayton (Xenia). SmartLink is the capability to remotely access your radio over the Internet without using a VPN. We will have several radios located worldwide that you can operate at the booth, from a PC running SmartSDR, a Maestro and the SmartSDR iOS app on an iPad. Because there may or may not be a local control point operator, the demo will be limited to receive only.
SmartSDR v2.0 will not be available for sale as it is not released yet. We still have some more work to do on it before we release it.9 -
Just be sure to watch your step while on the premises. I'm told that race horses will be on the property.
1 -
I fully understand. The homeowner looked at me yesterday and asked when was the roof going to be put on. I told her when the roof trusses get delivered!
0 -
Hi Tim. I am more than happy to have my flex available for the demonstration. The radio is connect to a 307 ft extended double zepp. 73, Mike1
-
Hi Tim, are you able to confirm if it have the ability for multiple clients to simultaneously connect to the radio at the same time?0
-
Thanks for the offer, but have it covered.0
-
I can confirm that is a feature planned for the 2.x release cycle. We will not be showing the multi-client feature at Hamvention.3
-
Ok, thanks for the response! Looking forward to v2!0
-
@JD
Apparently the foundation has been poured at least.
@Tim
If you have downloaded the Green Heron remote control app, I can let you into my remote 6700 and control the Radio on/off and RX antenna direction switching on both RX ports. The 4O3A 8X2 switch will put the right TX antenna on the radio in case there is Xmitting involved regardless of xmit antenna port selected.
Since there is no trip to Xenia for me, I hope someone videos some of the capabilities of V2.0 to share.
Regards
Larry k1UO
0 -
We have plenty of stations lined up. Thanks for the offer.
I am sure someone will be live streaming it. Maybe I'll do it on Facebook3 -
YES!! please livestream a demo of all the new stuff on facebook.
1 -
Tim, your post today has a bad link in it to the Smart Link flyer. Just wanted to let you know it is 404'ing. Didn't know how else to reach you on here.0
-
I'm guessing the link was taken down deliberately because it contained references to (still unannounced) products -- likely to be announced at Xenia.1
Leave a Comment
Categories
- All Categories
- 280 Community Topics
- 2.1K New Ideas
- 521 The Flea Market
- 7.5K Software
- 6K SmartSDR for Windows
- 143 SmartSDR for Maestro and M models
- 349 SmartSDR for Mac
- 247 SmartSDR for iOS
- 228 SmartSDR CAT
- 168 DAX
- 350 SmartSDR API
- 8.7K Radios and Accessories
- 7K FLEX-6000 Signature Series
- 835 Maestro
- 43 FlexControl
- 842 FLEX Series (Legacy) Radios
- 786 Genius Products
- 413 Power Genius XL Amplifier
- 274 Tuner Genius XL
- 99 Antenna Genius
- 237 Shack Infrastructure
- 161 Networking
- 397 Remote Operation (SmartLink)
- 124 Contesting
- 617 Peripherals & Station Integration
- 122 Amateur Radio Interests
- 855 Third-Party Software