Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR or 4O3A Genius Product Software?
SmartSDR v4.1.3 | SmartSDR v4.1.3 Release Notes
SmartSDR v3.10.15 | SmartSDR v3.10.15 Release Notes
The latest 4O3A Genius Product Software and Firmware
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

Using two 3rd Party programs. Need 2nd com port. How to config?

James Del Principe
James Del Principe Member ✭✭✭
edited June 2020 in FLEX-6000 Signature Series

Well, after much work and playing I got my Logger 32 to work and control frequency of the Flex 6500. Also, I got FLDIGI to work fully!!!   Wonder of wonders. But not both at the same time. No mystery here as they both used com 5.   OK, I need to use Smart SDR CAT to add a port. here's my experience.

I tried to add a port with SSDR CAT V 1.4.16.0     Serial "PORTS" tab / add a port / shows COM 6 - 16. Under ports map, com 6 says unknown & port 16 says CAT.

But on the 'MAIN' tab, "Connect 3rd party programs to PORT" still only shows com 5

FLDIGI is currently working. Logger 32 is no longer working even when I close FLDIGI.

In the computer device manager I see FLEX CTRL com 3 (which BTW no longer works) and virtual serial ports 14, 15, 16, 4, 5 & 6.

I set L32 for port 6 and then port 16 but neither worked. I think I need to see port 6 or 16 on the main tab under " connect 3rd party programs to port:"

Is this correct thinking?    Any suggestions?        Many Thanks, Jim


Answers

  • K9DUR
    K9DUR Member ✭✭
    edited January 2017
    Jim,

    The "Connect 3rd Party Programs to Port 5" message only applies to the 1st program you want to connect to the radio via CAT.  To add a 2nd program, open the SmartCAT control panel and add a dedicated port.  This will create another virtual serial port pair, for example COM6-COM16.  Simply tell the 2nd program to use COM6.  You can repeat this procedure as often as you need to.

    73, Ray, K9DUR
  • James Del Principe
    James Del Principe Member ✭✭✭
    edited September 2015
    Ray, thanks for the fast reply.    That is exactly what I did but when I configured Logger 32 for com 6 (or com 16 for that matter) it did not communicate with the Flex. I will try again. Maybe I just need to reboot everything instead of just closing programs. Thanks again for your suggestion. I'll try that now. 73, Jim
  • WX7Y
    WX7Y Member ✭✭✭✭
    edited June 2020
    don't you also need DDUtil to handle the COM port pares connection to the radio? 

    Bret
    WX7Y

  • James Del Principe
    James Del Principe Member ✭✭✭
    edited September 2015

    OK, Ray. You win the prize.     Always try one more time.    I now have both programs - FLDIGI and Logger 32 running at the same time and either one can take control. 

    Flex w/ Logger 32 - Com 5, 38400 baud, Kenwood TS480

    Flex w/ FLDIGI - Com 6, 38400 baud

    I can click on a station in L32 and it changes frequency which shows up in FLDIGI as well as the FLEX.   I can change the frequency in FLDIGI and it changes the FLEX.

    Problem solved.   The one thing I needed to do to make it all happen (after so many unsuccessful tries), was to reboot the computer.

    Thanks to aqll for the input.   73, Jim

  • James Del Principe
    James Del Principe Member ✭✭✭
    edited September 2015
    Ray, in my case, ignorance is truly bliss.     I am not familiar with DDUtil.    Is that a 3rd party program?   but it is now working.    73, Jim

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.

Comment As ...

Categories