Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
The latest SmartSDR Software:
SmartSDR v4.2.20 | SmartSDR v4.2.20 Release Notes
SmartSDR v3.10.15 | SmartSDR v3.10.15 Release Notes

The latest 4O3A Genius Product Software:
The latest 4O3A Genius Product Software and Firmware
How to Receive Technical Support::
If you are needing assistance with FlexRadio products, please refer to the product documentation or check the Help Center for known solutions. Need technical support from FlexRadio? It's as simple as creating a HelpDesk ticket.

When I try Pactor/RMS express/Smart SDR The radio transmits and acts correct but no signal out, on

Options
Kg5dwx
Kg5dwx Member ✭✭
edited September 2017 in SmartSDR for Windows
I am using a DR-7400, COM 10 in CAT, transmit light on red but pandaptor show low signal. Mike on ACC.

Answers

  • Neal_K3NC
    Neal_K3NC Member ✭✭
    edited February 2017
    Options
    Is DAX button on?
  • kr4k
    kr4k Member ✭✭
    edited September 2017
    Options
    I turned my Dragon audio up to 2200. Seemed to work. However, I have not been consistent connecting to anything with the MODEM. MODEM works well on TS-2000.
  • Kg5dwx
    Kg5dwx Member ✭✭
    edited December 2016
    Options
    Dax off
  • Kg5dwx
    Kg5dwx Member ✭✭
    edited February 2017
    Options
    I'll check the dragon audio, worked great on ft-857, thanks.
  • Neal_K3NC
    Neal_K3NC Member ✭✭
    edited July 2015
    Options
    Try Dax On
  • Ed.G
    Ed.G FlexRadio Employee ✭✭
    edited December 2016
    Options
    In order to run PACTOR with the 6000 series radios there are a couple of things that have to be in place:

    1. The slice used for PACTOR must be in DIGU or DIGL with a filter wider than 3k. This will make SmartSDR use lower latency filters to decrease turnaround time. 

    2. Make sure the audio levels are set properly. The MIC level meter should peak right under 0. 

    3. Although you can use AGC with PACTOR on some paths you can save a few milliseconds of latency by setting the AGC to OFF. 

    4. Make sure PROC and the EQ are off as well. 
  • Kg5dwx
    Kg5dwx Member ✭✭
    edited February 2017
    Options
    This works
    Flex:
    DIGIU at 5K
    Mike=ACC
    EQ=off
    PROC=off (Default on DIGIU)
    DEXP=off (Default on DIGIU)
    Set Comport you are using to Active in CAT

    RMS Express:
    TNC setup:
    PSK=4000 (max)
    FSK=4000 (max)
    TX delay 0 to 20
    Radio:
    Radio - Flex
    Band USB DIGITAL

    Seems to work!

    Rodney H. Warner
    KG5DWX
    512-496-4301 cell





Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.

Comment As ...

Categories