Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
PR781 Heil Mic Issue
Options
Joseph Rodick
Member
I have a flex 6300. I am using a PR781 Heil Mic, with the Bal Cable. I am getting reports of motor boating audio, almost like computer generated tone. When I use the Flex Mic supplied with the 6300 the motor boating is gone. Any Clues?
0
Comments
-
Sounds like RF is coming through the balanced cable, I would put a toroid on it.1
-
just added four toroid coils on the balanced cable, till getting the motor boating sound using the PR7810
-
Still sounds like you are getting rf in the balanced line (not sure how but if it doesn't happen when coming through the front panel but does through the balanced line, thats all I know it can be!)
730 -
Just ordered another cable from flex. Thank you for your assistance.
Joseph
WB4SSG
0 -
6.1.2 Supported Microphone Types
The FLEX-6000 front microphone connector can support either a dynamic or an electret
microphone. This is an unbalanced high impedance input. The electret bias voltage is not
enabled by default, and must be enabled by SmartSDR. The DB 15 in the back does not provide a balanced input It provides a Plus audio input and a Frame ground .0 -
I had this issue the other day with my 6300. Was using a heil headset with the adapter for the 8 pin mic connection in front of the radio. Several stations said I had the "motor boating" on my signal. I turned on the monitor and sure enough, I could hear it. I unplugged the headset and plugged it back in and it's not done it since.
0 -
While adding a toroid to your mic cable may be the answer, people need to understand that all toroids are not created equal. Mix 31 toroids work best for HF frequencies. Mix 43 will work above 10mhz. Unless you are sure of the composition of the toroids you are using, they may not help at all. Almost never are toroids bought at hamfests identified.
Jon...kf2e
2
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.1K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 331 SmartSDR for Mac
- 243 SmartSDR for iOS
- 222 SmartSDR CAT
- 163 DAX
- 348 SmartSDR API
- 8.6K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 765 Maestro
- 41 FlexControl
- 836 FLEX Series (Legacy) Radios
- 733 Genius Products
- 393 Power Genius XL Amplifier
- 255 Tuner Genius XL
- 85 Antenna Genius
- 229 Shack Infrastructure
- 153 Networking
- 370 Remote Operation (SmartLink)
- 120 Contesting
- 583 Peripherals & Station Integration
- 115 Amateur Radio Interests
- 812 Third-Party Software