Welcome to the FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
The latest SmartSDR Software:
SmartSDR v4.2.20 | SmartSDR v4.2.20 Release Notes
SmartSDR v3.10.15 | SmartSDR v3.10.15 Release Notes

The latest 4O3A Genius Product Software:
The latest 4O3A Genius Product Software and Firmware
How to Receive Technical Support::
If you are needing assistance with FlexRadio products, please refer to the product documentation or check the Help Center for known solutions. Need technical support from FlexRadio? It's as simple as creating a HelpDesk ticket.

Tuning frequency with SSB

Options
Bob N7ZO
Bob N7ZO Member ✭✭
edited June 2020 in New Ideas

When I press the TUNE button with 1.2.1 SSDR, it transmits a
carrier on the CW pitch even when I am in SSB mode.  In general, tuning at “0” Hertz is less offending to SSB QSO’s.   It would be an improvement to move the tuning frequency to the SSB carrier frequency (“0” Hertz).

(Yes, I could move the VFO and then move back, but we are trying to improve ease of operation here.)

6
Up Down
6 votes

In Review · Last Updated

Comments

  • Ken - NM9P
    Ken - NM9P Member ✭✭✭
    edited June 2020
    Options
    Many of us have made this suggestion previously. In the mean time, I simply use XIT to shift the freq to zero beat and tune up. But then I need to remember to zero out the XIT before transmitting! I have forgotten this several times! It is hard to bust a pileup on the wrong TX frequency!
  • Jim Gilliam
    Jim Gilliam Member ✭✭
    edited June 2020
    Options

    I agree, I think it just causes unnecessary QRM. I believe the Flex 3000 and 5000 are on the center frequency. Not sure why they changed this operation.


    Jim, K6QE

  • Ken - NM9P
    Ken - NM9P Member ✭✭✭
    edited December 2016
    Options
    Yes, they are, and the 1500 too.
  • Bob N7ZO
    Bob N7ZO Member ✭✭
    edited February 2017
    Options
    Ken, always happy to stumble upon an existing suggestion.  Re-searching with better keywords shows that the last discussion on this was two to nine months ago.  But no likes lately.  Perhaps FRS has a decay algorithm they apply to old likes.  :-)
  • Ken - NM9P
    Ken - NM9P Member ✭✭✭
    edited June 2020
    Options
    Thanks for the "bump!" It seems to me that this issue should be a simple formula to change. But things aren't always as easy as they seem!
  • Jay Nation - NO5J
    Jay Nation - NO5J Member
    edited September 2014
    Options
    And an extra bump, I wasn't aware that SSDR handled this differently and found it odd that someone else seemed to be aggravating the others on the frequency with carriers that only "I" couldn't hear. 
  • Bob N7ZO
    Bob N7ZO Member ✭✭
    edited February 2017
    Options
    Jay, thanks for the bump, but I don't think we need it now.   This seems to have been implemented in 1.3.   Hooray!
  • Ken - NM9P
    Ken - NM9P Member ✭✭✭
    edited December 2016
    Options
    I was very glad to see that "Tune on zero beat" in SSB mode was added to release V 1.3. But now I need to retrain myself to stop grabbing the XIT when I get ready to tune! I had adapted quickly, so it wasn't a big problem. But it is very nice, now.
  • Jay Nation - NO5J
    Jay Nation - NO5J Member
    edited September 2014
    Options
    Okay, I hadn't noticed it was fixed yet. I'll Bump your Hooray! then. Excuse the noise folks they fixed it already! 

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.

Comment As ...

Categories