Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.8.19 and the SmartSDR v3.8.19 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.8.19 and the SmartSDR v3.8.19 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Expand the use of your C232HM cable to meet user needs
I have a Flex 6500, an Expert 1.3K-FA amp, and an Ameritron RCS-10 antenna switch for my 5-band quad antenna.
The manual switch controller is in my shack, while the outdoor switch is at the top of my tower (at the antenna). The switch controller sends 3-bit BCD codes to the outdoor switch. In order they are set to 10m = 101 (5), 12m = 001 (4), 15m = 110 (3), 17m = 010 (2), and 20m = 100 (1). I'd like your cable to send these codes to my antenna switch.
Your 4-bit cable responds to my VFO setting, so 20m = 0101 (5), 17m = 0110 (6), 15m = 0111 (7), 12m = 1000 (8), and 10m = 1001 (9).
Your cable responds to the code in your program. It does this properly. I'm asking if you could expand the use of your cable to respond to user needs. This cable is already programmable. This sounds like a rather easy request.
The manual switch controller is in my shack, while the outdoor switch is at the top of my tower (at the antenna). The switch controller sends 3-bit BCD codes to the outdoor switch. In order they are set to 10m = 101 (5), 12m = 001 (4), 15m = 110 (3), 17m = 010 (2), and 20m = 100 (1). I'd like your cable to send these codes to my antenna switch.
Your 4-bit cable responds to my VFO setting, so 20m = 0101 (5), 17m = 0110 (6), 15m = 0111 (7), 12m = 1000 (8), and 10m = 1001 (9).
Your cable responds to the code in your program. It does this properly. I'm asking if you could expand the use of your cable to respond to user needs. This cable is already programmable. This sounds like a rather easy request.
1
Leave a Comment
Categories
- All Categories
- 286 Community Topics
- 2.1K New Ideas
- 526 The Flea Market
- 7.5K Software
- 6K SmartSDR for Windows
- 146 SmartSDR for Maestro and M models
- 354 SmartSDR for Mac
- 249 SmartSDR for iOS
- 229 SmartSDR CAT
- 170 DAX
- 352 SmartSDR API
- 8.7K Radios and Accessories
- 7K FLEX-6000 Signature Series
- 15 FLEX-8000 Signature Series
- 840 Maestro
- 43 FlexControl
- 846 FLEX Series (Legacy) Radios
- 790 Genius Products
- 414 Power Genius XL Amplifier
- 275 Tuner Genius XL
- 101 Antenna Genius
- 243 Shack Infrastructure
- 166 Networking
- 404 Remote Operation (SmartLink)
- 128 Contesting
- 628 Peripherals & Station Integration
- 125 Amateur Radio Interests
- 861 Third-Party Software