Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.8.19 and the SmartSDR v3.8.19 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.8.19 and the SmartSDR v3.8.19 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
My TX Band Settings has no profile
hayaya
Member, Unconfirmed ✭
Hi
After updating FLEX-6400M to ver3.3.32.8203, I am doing the initial settings. There are too many problems and I don't know what to start with, but first I want to get a waterfall in the RX mode.
With the Farmware running, only two S meters are displayed at the top of the screen.
If I do not operate it, the waterfall will be displayed and disappear again. Looking at MENU> TX Band Settings, all the settings are missing. The manual shows the table, but nothing but the table item rows. I expect that if this is fixed, the waterfall will be displayed in a stable manner.
I inadvertently did not confirm the operation with the version at the time of purchase and updated to the current version. So I don't remember what the original version was.
Please tell me how to cure it.
After updating FLEX-6400M to ver3.3.32.8203, I am doing the initial settings. There are too many problems and I don't know what to start with, but first I want to get a waterfall in the RX mode.
With the Farmware running, only two S meters are displayed at the top of the screen.
If I do not operate it, the waterfall will be displayed and disappear again. Looking at MENU> TX Band Settings, all the settings are missing. The manual shows the table, but nothing but the table item rows. I expect that if this is fixed, the waterfall will be displayed in a stable manner.
I inadvertently did not confirm the operation with the version at the time of purchase and updated to the current version. So I don't remember what the original version was.
Please tell me how to cure it.
0
Answers
-
Open a Help Desk Ticket https://helpdesk.flexradio.com/hc/en-us/requests/new
0 -
Hi,Erik
Thanks for your advice.
After posting the question, I downloaded all the updatable firmware and applied it in chronological order, and now the waterfall is displayed normally in Ver3.3.32.8203. The TX Band Settings table is now displayed like a manual.
hank you. :)0 -
That is a relief!
0
Leave a Comment
Categories
- All Categories
- 280 Community Topics
- 2.1K New Ideas
- 521 The Flea Market
- 7.5K Software
- 6K SmartSDR for Windows
- 143 SmartSDR for Maestro and M models
- 349 SmartSDR for Mac
- 247 SmartSDR for iOS
- 228 SmartSDR CAT
- 168 DAX
- 351 SmartSDR API
- 8.7K Radios and Accessories
- 7K FLEX-6000 Signature Series
- 838 Maestro
- 43 FlexControl
- 842 FLEX Series (Legacy) Radios
- 786 Genius Products
- 413 Power Genius XL Amplifier
- 274 Tuner Genius XL
- 99 Antenna Genius
- 237 Shack Infrastructure
- 161 Networking
- 398 Remote Operation (SmartLink)
- 124 Contesting
- 617 Peripherals & Station Integration
- 122 Amateur Radio Interests
- 856 Third-Party Software