Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Panadapter #1 problem?
Options
N4AB
Member ✭✭
Flex 6700 Radio While Running 2 Panadapters on 20 meters today I noticed that the first Pan had a slowly rising slope on the higher frequency end of the scale. So I set both pans up to be identical (frequency, vertical and horizontal scale, Averaging, FPS, bandwidth, etc.). The result was a definite 5 db slope across Panadapter #1. To double check on which one was right, I set all 8 Panadapters to be identical. The other 6 pans agreed with pan 2 very well as shown in the attached photo. Where the 7 pans showed the noise floor to start and end at approximately -115 db, pan 1 started at -115 db but then sloped up to end at approximately -110. Since the picture is small compared to the 43-inch monitor (TV) it is hard to make out all the details, but the difference can be seen between the end of pan 1 (upper left) and start of pan 5 (upper right). I wonder if anyone else has this problem (if it is a problem) or should I submit it to the Flex tech guys for investigation. Al, N4AB
0
Comments
-
AL
Look at slice A your on Antenna 2 for receive the rest are on antenna 1.
Ian0 -
Well that was ****, and I spent an hour making sure every thing was the same, duh. thanks Ian.0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 328 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 810 Third-Party Software