Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
Need the latest SmartSDR, Power Genius, Tuner Genius and Antenna Genius Software?
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
SmartSDR v3.7.4 and the SmartSDR v3.7.4 Release Notes | SmartSDR v2.12.1 and the SmartSDR v2.12.1 Release Notes
SmartSDR v1.12.1 and the SmartSDR v1.12.1 Release Notes
Power Genius XL Utility v3.8.8 and the Power Genius XL Release Notes v3.8.8
Tuner Genius XL Utility v1.2.11 and the Tuner Genius XL Release Notes v1.2.11
Antenna Genius Utility v4.1.8
If you are having a problem, please refer to the product documentation or check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.
Monitoring DAX audio
Options
Greg
Member ✭✭
This is not really a question rather an observation.
I know right now monitoring (MON) the DAX tx audio is not available. But....
During the RTTY NAQP this weekend while transmitting I accidentally bumped the tuning knob (flex control) and as soon as I did I was hearing the transmitted DAX audio. This happens only when you change freq while transmitting from DAX. Obviously not a good thing to do but may be a clue to eventually get this function without having to bump the frequency.
73
Greg
I know right now monitoring (MON) the DAX tx audio is not available. But....
During the RTTY NAQP this weekend while transmitting I accidentally bumped the tuning knob (flex control) and as soon as I did I was hearing the transmitted DAX audio. This happens only when you change freq while transmitting from DAX. Obviously not a good thing to do but may be a clue to eventually get this function without having to bump the frequency.
73
Greg
0
Comments
-
This defect has been previously identified and is in the bug tracker for further investigation. Thanks for the confirming report.
0 -
FLEX:
It would be Nice to have a TAB along side the TABS shown on the Transmit Panel that when selected would display the DAX Control panel for the Active slice. A DAX Tab next to the "EQ" tab when selected would put the DAX control panel showing RX and TX Status on the Transmit Panel following the same size of the other displayed boxes. It would show the DAX RX/TX status for the active Slice. When moving between Slices, Digital modes, I have to bring up the DAX Control Panel to verify that it is working for selected Slice.
Since I am running two monitors, selecting the DAX Icon in the control panel will open the DAX Control panel in different locations on one of the two monitors. Usually opens on the Slices.
Bill
W4EY
0 -
This really isn't applicable to Greg's post and is better to start a new Idea post so others can comment on it. Please reference the new topic here: DAX Control panel on side bar0
Leave a Comment
Categories
- All Categories
- 246 Community Topics
- 2.1K New Ideas
- 488 The Flea Market
- 7.3K Software
- 5.9K SmartSDR for Windows
- 134 SmartSDR for Maestro and M models
- 328 SmartSDR for Mac
- 241 SmartSDR for iOS
- 224 SmartSDR CAT
- 161 DAX
- 343 SmartSDR API
- 8.5K Radios and Accessories
- 6.9K FLEX-6000 Signature Series
- 768 Maestro
- 42 FlexControl
- 836 FLEX Series (Legacy) Radios
- 726 Genius Products
- 391 Power Genius XL Amplifier
- 251 Tuner Genius XL
- 84 Antenna Genius
- 222 Shack Infrastructure
- 149 Networking
- 370 Remote Operation (SmartLink)
- 118 Contesting
- 582 Peripherals & Station Integration
- 116 Amateur Radio Interests
- 810 Third-Party Software