Welcome to the new FlexRadio Community! Please review the new Community Rules and other important new Community information on the Message Board.
If you are having a problem, please check the Help Center for known solutions.
Need technical support from FlexRadio? It's as simple as Creating a HelpDesk ticket.

Can't turn QSK off

Hi folks,

Using a 6400 (without internal tuner) here with SSDR 3.1.12. While operating CW during the recent RAC Winter contest, I found that I could not turn off QSK. I tried restarting SSDR and the radio and neither had any impact. It also does not matter if N1MM+ is running or not. Any suggestions?

73,
Pierre VE3KTB

Best Answer

  • Tim - W4TME
    Tim - W4TME Administrator, FlexRadio Employee admin
    Accepted Answer

    The radio has to be in several different antenna configurations for the radio (the hardware) to be capable of QSK operation. The QSK indicator communicates this hardware capability, not that you are actually operating in QSK mode. Whether or not you are operating in QSK mode is dependent on the CW delay setting.

    How to operate in QSK mode is covered in the SmartSDR Software User Guide, section 23.2 CW Transmitting.

Answers

  • KD0RC
    KD0RC Broomfield, COMember ✭✭✭

    Hi Pierre, Did you try changing the CW Delay?


    73,

    Len, KD0RC

  • No, I haven't. I have only clicked the Breakin button, and it does change colour. What value should I set the delay to?
  • And I should add that the qsk indicator in the flag does not change.
  • KD0RC
    KD0RC Broomfield, COMember ✭✭✭

    I only get the QSK indicator to change if I turn TX on or off. For 24 WPM, a delay of 200 seems about right. To try it out without transmitting, turn your RF Power to 0, turn Breakin on, and make sure TX is on. Now you can get a feel for how much delay based on your WPM by watching the panadapter. If it jumps between elements, characters or words, you need more delay. If it holds the receiver quiet for too long, you need less.

    73,

    Len

  • KD0RC
    KD0RC Broomfield, COMember ✭✭✭

    OK, I did find a QSK button at the top of the CWX setup screen. Apparently, it only affects CWX messages and anything you type into the CWX screen. The Delay control affects CWX and the paddles.

    73,

    Len

  • Lionel
    Lionel Member ✭✭

    I use QSK most of the time. Delay at 0, filter set to low latency position.

    Someone gave me a tip to turn on FDX and this made a noticeable difference but I don't know why.

    This keeps me a happy QSK op at 25wpm or so. I've never used CWX.

    I am always RX/TX on Ant 1, usually not split, though QSK works just fine.

    Rarely I increase the delay and effectively exit QSK.

  • Tim, thanks for the explanation on how it works. I had read that section, but I misunderstood the statement "The BREAKIN control allows automatic PTT when the key is pressed" inferring it meant that turning BREAKIN off would mean no qsk.

    I did some tests with the delay setting and determined that at 24 wpm I had no breakin from 40 ms up. I decided on a delay of 50 ms to give some leeway.

    This was all generated because my Heathkit HL2200 has very loud clunking relays that literally caused me to jump when I transitioned from SSB to CW during the RAC contest.

    Thanks to all for your input!


    73,

    Pierre VE3KTB

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.